Screenint OPEN ROLL, Installation Manual, Page: 2 / 5

INTRODUCTION
Thank you for purchasing the motorized Open Roll projection screen. This screen is made entirely in Italy with first-class materials, including a high quality projection surface
to guarantee excellent performance for your installation.
WARNINGS
Before installing the screen, please read the following instructions carefully. We would recommend that these instructions are stored safely for future reference.
When opening the packaging of the screen, please DO NOT USE CUTTERS or OTHER SHARP TOOLS that can damage the screen inside. During opening the packaging and
during installation, it is reccomended to use work gloves.
Depending on the screen weight, it has to be handled by at least two or three persons taking care to the following ratio KG/PERSON: MALE 25 kg. – FEMALE 15 kg.
The manufacturer does not take responsibility for any damage to property or personal injury if the screen is used outside of recommended specifications or in case of
incorrect/poor quality installation.
CERTIFICATIONS
Motorized screens Open Roll are certified.
The surfaces for projection used on the products are cadmium-free and are fire-proof certified as follows:
- class M1 – MATTE WHITE, FRONTREAR, REAR PLUS
- class B1 – WHITE, MICROHOLES
WARRANTY
This projection screen is guaranteed 2 years from the purchase date for manufacturing defects.
Responsibility is limited to repairing or substitution of the defected components and without any other charge at our expense.
Warranty is officially voided if
the screen has been dismantled or it is returned with collision damage or defective due to incorrect installation. Repairs must be carried out
by an Approved Screen International Certified Engineer.
Warranty is officially voided if:
1)
the motor is removed / dismantled;
2) the screen has been transit damaged;
3) the instructions regarding the electrical connections have not been followed;
4) the products have to be installed following the electric regulations (CEI) and the other local specific laws;
5) in the installation are used electric interfaces that does not allow the correct time lapse between up and down operation (complete cut down of electric power on both
phases for half a second)
6) electrical accessories have been used that are incompatible with the screen motor causing damage to its internal components;
7) the motor end stops have been modified without the authorisation of the factory;
8) the sticker regarding the serial number of the product has been altered, deleted, removed or is illegible.
DO NOT install this screen nearby or over heating or air conditioning systems, because PVC is a plastic material which dilates and remains damaged if it is subjected to heat
and/or cool air.
DO NOT install this screen either facing direct sun light or blocking a window as PVC could be damaged and make waves for the explanations given above.
The PVC cloth is very sensitive to temperature range. We advise to mount the screen in environments with an ambient temperature in the range of 18°-25°C.
We advise you to wait 2 hours for the screen to acclimatise before using the screen after delivery, especially if screen is brought into a warm environment from cold.
In case the screen is new or it has been rolled up for long time, roll down the screen and leave it open for ca. 24/48 hrs. with an ambient temperature in the range of 18°-25°
C in order to get a perfect flatness of the cloth
DO NOT WASH the projection surface with alcohol or solvent nor with commercial cleaners. Every now and then dust the surface with a dry and clean duster.
Please, be very careful because any kind of stain on projection surfaces is inerasable.
The screen has to be used showing the total projection sizes indicated on the packaging; therefore it is NOT allowed to adjust the end stops to restrict the total drop or
extend it. Restricting the total drop of the screen is likely to cause your screen surface to lose its flatness.
When the screen is not completely rolled down (as by factory setting), flatness of the cloth is NOT guaranteed and therefore not covered by warranty.
DO NOT HANG TO THE SCREEN and DO NOT HANG ANY OBJECT to it. Please take care that children DO NOT PLAY with the screen as they can get severely injured.
The manufacturer will not accept returns of screens for repair without manufacturer’s authorization (RMA number) and without a suitable packaging.
INSTALLATION INSTRUCTIONS
1. ASSEMBLY
The product has to be installed and used conform to the laws in force within the country where the product is used.
Our screen is supplied with ceiling brackets suitable for fixing it at the ceiling by heavy duty bolts (not supplied) specific for the type of material to be
secured to. During installation, please take care to use security belts in order to secure the screen.
Pay attention to mount the left and right brackets in the right direction and at the exact distance (see Fig. 1). Prior to installing the roller screen, ensure
the ceiling is suitable for the loading induced by the weight of the screen. Please be aware that the screen is heavy and two or more people may be
required to lift the screen safely. Once the brackets are fixed to the ceiling, plug the pinion “D” into the ball bearing hole “C” and hook the motor “B”
with the bracket “A” using the stop ring “E” that has to be fixed with the supplied screw (Fig. 2 and Fig. 3)
.
Now, fix with an Allen-key the screws
located at the left side of the bearing hole “C”. Release the screen transport straps.
CAUTION: CHECK EVERY 6 MONTHS THAT SCREWS, WALL PLUGS AND BRACKETS ARE IN GOOD CONDITIONS AND WELL TIGHTENED.
2. ELECTRIC CONNECTION
Connection of the power supply must be carried out by qualified personnel only, using the diagram showed on Fig. 4. Pay attention to wire colours and
fix the switch near the screen as we recommend the projection surface to be visible to the operator.
Never connect more than one screen motor to the same switcher . Use the supplied switch only.
IN CASE OF MAINTENANCE, UNPLUG THE POWER SUPPLY.
In case the screen is controlled via relais, take care that the control system is programmed so there is no tension on the relais for at least 1 sec. during
switching between rolling up and rolling down operations and viceversa.
IT IS FORBIDDEN TO STAY UNDER THE PROJECTION SCREEN.
IT IS FORBIDDEN TO USE THE PROJECTION SCREEN OUTDOOR.
ONCE PROJECTION IS FINISHED, ROLL UP THE SCREEN (keeping the screen rolled down can cause
deformations to the projection surface.
INSTALLATION MANUAL
ENGLISH
OPEN ROLL