manualshive.com logo in svg

Scotsman UF424A-1A, Technical Manual

Share
Download
Scotsman UF424A-1A Technical Manual Download Page 24

UF424 / UN324 Technical Manual

September 2017

Page 24

Panel Removal

Top Panel

Requires back access
1.  Remove three thumbscrews holding top panel to 

back panel.

2.  Pull top panel back slightly to release it from the 

top of  the machine, then lift up and off the unit.

Note: Upper brace may come with top panel, it is not 

attached to the unit.

Door

1.  Remove top panel.
2.  Push door to full open, then lift back end up and 

remove two bushings. Retain the bushings.

3.  Pull door up thru the slot until the last two 

bushings appear. Remove and retain them.

4.  Pull door up and out of the machine

Side Panel

1.  Remove front, top and back panels.
2.  Remove two screws at each side of the top edge 

of the unit.

Note: The front screw on the top of each side will not 

be tightened fully, its correct position is slightly above 

the surface of the top  so that the head will fit into the 

key hole slots in the top panel.

Summary of Contents for UF424A-1A




































Reviews:

No comments

Brands by name

Popular brands

Load more brands