Scotsman FM1200 Page 31 Service Manual Download | Manualshive

Page: 31 / 31

background image

Water Level
1. Unplug “water sen” connector from control
board.
2. Plug “water sen” connector from Scotsman
tester into circuit board.

a. Move “water” switch on tester to No Water

position. The No Water light on the circuit
board should go ON. If not, replace the circuit
board.

b. Move the “water” switch on the tester to the

Water position.  The No Water light on the
board should go OFF.  If not replace the circuit
board.  If the light does go off, replace the
water level sensor.
If the Bin Empty light is ON, wait 10-20
seconds for the machine to start. The machine
should start.

LIGHT ON

WATER SENS

SWITCH TO

“NO WATER”

CIRCUIT BOARD TESTING

LIGHT OFF

SWITCH TO

“WATER”

FM1200

October, 1991

Page 31

«
...
29
30
31

Summary of Contents for FM1200
































Reviews:

No comments

Related manuals for FM1200

Brand: Faema Pages: 328

Brand: Quick MILL Pages: 16

Brand: Hoshizaki Pages: 25

Brand: Proctor-Silex Pages: 19

Brand: Hamilton Beach Pages: 24

FUTURMAT SENSIUS

Brand: Quality Espresso Pages: 44

Brand: Lagrange Pages: 62

Brand: Gaggia Pages: 4

Brand: Salton Pages: 9

Brand: U-Line Pages: 66

Brand: Caffitaly System Pages: 64

Cafe Classic CC 101, CC 102

Brand: AEG Pages: 8

Brand: AEG Pages: 9

Brand: AEG Pages: 33

Brand: AEG Pages: 20

Brand: AEG Pages: 10

Brand: AEG Pages: 81

Brand: AEG Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands