Scotsman ECC1200 Series Page 20 Service Manual Download

Page: 20 / 57

EH330, EH430 and ECC Condensing Unit

Remote Low Side Cuber Service Manual

May 2015

Page 19

Reference for Start Up: Controller Operation

he controller and remote switch panel have four

indicator lights and the On and Off buttons.

Indicator Lights

•

Power - on when there is power to the controller

•

Status - on in ice making mode

•

Water - on and blinking when there is no water

•

De-scale & Sanitize - on when it is time to clean

the machine

Code Display

•

Displays status and diagnostic codes

Push Buttons

•

Off

•

Manual Harvest

•

Clean

Lower light and switch panel

Component indicator lights

•

Fan - not used on this model

•

Water Pump - on when the pump is

•

Purge Valve - on when the purge valve is

•

Water Solenoid - on when the inlet water solenoid

valve is

•

Hot Gas - on when the vapor inlet valve and

harvest assist solenoid / mechanism have power

•

Compressor - on when the compressor contactor

is energized

•

Ready to Harvest - on when the ice thickness

sensor has water touching it

•

Sump Empty - on when there is no water touching

the mid-length probe

•

Sump Full - on when water is touching the

shortest probe

•

SW2 - on when the curtain is open

•

SW1 - on when the curtain is open

Cycle Definitions:

Freeze: The refrigeration system is operating to

remove heat from the evaporators. The compressor,

fan motor, and water pump are on.

Harvest: The refrigeration system and water system

are operating to harvest the ice and rinse the

reservoir. The compressor is on for the full cycle, the

pump is on until the purge valve closes.

The inlet water valve opens and refills the reservoir.

The vapor and condenser by-pass valves are open

during the entire harvest cycle, as are the harvest

assist mechanisms.

Summary of Contents for ECC1200 Series


























































Search results

Summary of Contents for ECC1200 Series

Reviews:

Related manuals for ECC1200 Series

Brands by name

Popular brands

Scotsman ECC1200 Series, Service Manual

Search results

Summary of Contents for ECC1200 Series

Reviews:

Related manuals for ECC1200 Series

Brands by name

Popular brands