Read pages
1982-91 Pontiac 6000
3-7 for kit
assembly.
Radio Removal:
1. Loosen the screw securing the radio trim panel to the left side of the glove box.
2. Carefully pull the panel outward to relieve the clips retaining the left side of the panel. Remove the trim
panel.
3. Remove the four screws retaining the radio, and pull the radio out of the cavity.
4. Disconnect the antenna, speaker leads and all the electrical connections, then remove the radio.
RIGHT
"A1" BRACKET USE HOLE #2
LEFT
"B1" BRACKET USE HOLE #2
LADO DERECHO
"A1" SOPORTE USA ABERTURA NO. 2
LADO IZQUIERDA
"B1" SOPORTE USA ABERTURA NO. 2
2
2
TRIM
BRACKET
FRONT OF KIT
CORTA EL
SOPORTE
FRENTE DE
1
1
"C2" BRACKET USE HOLE #1
ESTUCHE
"C2" SOPORTE USA
"D2" BRACKET USE HOLE #1
ABERTURA NO. 1
"D2" SOPORTE USA ABERTURA NO. 1
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
Read pages
1991-94 Saturn SC, SL, SL1, SL2
3-7 for kit
assembly.
Radio Removal:
1. Using a panel removal tool/screwdriver, carefully pry outward on the dash bezel to release the clips and
remove the bezel.
2. Extract the two screws
securing the radio to the
dash. Pull the unit out of the
"C1" BRACKET
dash, unplug the
USE HOLE #2
"C1" SOPORTE
USA ABERTURA NO. 2
connectors and remove the
radio.
"B1" BRACKET
USE HOLE #2
"B1" SOPORTE
USA ABERTURA NO. 2
TOP
TOPE
FRONT OF KIT
FRENTE DE ESTUCHE
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
32
1990-93 Chevrolet Lumina APV
Read pages
3-7 for kit
1990-93 Oldsmobile Silhouette
assembly.
1990-93 Pontiac Trans Sport
Radio Removal:
1.
Open the glove box to access the two screws on the right side that secure
the radio trim.
2. From the driver’s side remove the three screws from the belly trim piece: one at the hood release, one
above the diagnostic connector and one at the lower backside of the console trim.
3. Release the spring clips from the top of the lower steering column trim piece and remove the trim.
4. Extract the two screws securing
WASHER
"C1" BRACKET USE HOLE #2
ARANDELA
the left side of the radio trim and
"C1" SOPORTE USA
remove the trim.
ABERTURA NO. 2
CUT OFF TAB
(TWO BRACKETS)
5. Using a socket wrench, reach
ROMPE LENQUETE
CARRIAGE BOLT
(DOS SOPORTES)
PORTE
TOP
PERNO DE
under the radio and remove the nut
securing the bottom of the radio.
6. Extract two screws from the top
TOPE
FLANGE
radio bracket, pull the unit out,
NUT
"D1" BRACKET
USE HOLE #2
disconnect connectors and remove
TUERCO REBORDE
" D1" SOPORTE USA
radio.
ABERTURA NO. 2
BOTTOM
FONDO
USE THE SUPPLIED CARRIAGE BOLTS & NUTS TO MOUNT THE KIT PANEL TO THE SUB-DASH.
Usa los pernos de portey tuercos proveidos para montar la tablera estuche al tablero-sub.
Read pages
1997-00 Chevrolet Malibu
3-7 for kit
assembly.
Radio Removal:
1. Carefully pop out plastic collar around ignition key and remove.
2.
Carefully
"A1" BRACKET
LEFT SIDE
"B1" BRACKET
pop out
USE HOLE #2
RIGHT SIDE
USE HOLE #2
LADO DERECHO
radio trim,
"A1" SOPORTE
LADO
"B1" SOPORTE
IZQUIERDA
USA ABERTURA NO. 2
USA ABERTURA
NO. 2
unplug
lighter and
remove.
3. Extract two
7mm screws
holding radio in,
unplug all
connectors and
remove radio.
FRONT OF KIT
FRENTE DE ESTUCHE
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
Read pages
1986-88 Chevrolet Monte Carlo
3-7 for kit
assembly.
1986-87 Chevrolet El Camino
Radio Removal:
1. Remove the two screws from the top of the radio trim panel and the two screws from the bottom edge of
the trim panel.
2. Remove the four screws which secure the radio, slide the radio out of the dash cavity and disconnect the
wiring
LEFT
RIGHT
"B1" BRACKET USE HOLE #1
"A1" BRACKET USE HOLE #4
LADO IZQUIERDA LADO DERECHO
"A1" SOPORTE USA
connectors.
"B1" SOPORTE
USA ABERTURA
NO. 1
3. Remove the
ABERTURA
NO. 4
4
radio.
2
TRIM
BRACKET
CORTA EL
FRONT OF KIT
4
SOPORTE
2
FRENTE DE
"C2" BRACKET
ESTUCHE
USE HOLE #4
"D2" BRACKET USE HOLE #1
"C2" SOPORTE USA ABERTURA NO. 4
"D2" SOPORTE USA ABERTURA NO. 1
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
21
