Note: Connect the (HAR-1) harness to the MCM only after installation is completed.
If the battery is to be removed, disconnect this connector first. Reconnect only
after battery terminals are reconnected
.
Using the T-tap Connectors
1) Place female T-tap connector over wire to be tapped. Close and squeeze until it
snaps.
2) Slip male T-tap connector over hinged end of the female connector.
Motorcycle Wire
1)
Female T-tap
2)
Female T-tap
Male T-tap
Motorcycle
Wire
Wire from (GEN-1)
Operation Instructions
Violation Display
When the system is disarmed, the turn signals will flash to indicate that there has been an
alarm trigger. The lights will flash once to indicate that the system has been disarmed and
additional flashes indicate the following trigger has occurred:
1 flash then 1 additional flash = Shock Trigger
1 flash then 2 additional flashes = Tilt Trigger
1 flash then 3 additional flashes = Perimeter Sensor Trigger
1 flash then 5 additional flashes = Ignition Trigger
6
Operation Instructions (Cont.)
Selecting Arming Modes
rLiNK can be manually armed and disarmed using the button on the remote, or
automatically armed and disarmed by turning your ignition key on and off. When the
alarm is first installed, the alarm will arm 5 seconds after the HAR-1 harness is plugged in.
The default setting is to arm with the perimeter sensor (SN-5) on.
Automatic Arming
When keeping the remote in range and turning your key on, the alarm will recognize the
remote and disarm the alarm. Once you turn the key off, the alarm will wait 5 seconds
and arm again.
Manual Arming- Press and hold the button for 1 second. When you manually disarm the
alarm, you are turning the auto arm off. To turn auto back on simply arm the alarm with
the remote and go back to using the key to arm and disarm.
Manual Arming with Perimeter Sensor- Press and hold the button for 5 seconds. The turn
signals will flash normally then will flash left-right twice to confirm the system is armed with
the Perimeter Sensor active.
While armed double tap the button on your remote and the alarm will chirp once and
the turn signal lights will flash once. The alarm is now manually disarmed and will not
automatically arm. The alarm will only arm again when you push and hold the button on
the remote for 1 second. To return to automatic arming, arm the alarm and go back to
using the key.
Setting Perimeter Sensor Default
1.
To select between perimeter sensor on and off, double tap the button on
the remote to manually disarm the alarm.
2.
Turn your ignition key on-off-on, double tap the button quickly and the siren
will chirp 2 or 3 times to let you know whether the perimeter sensor is on or
off.
(If equipped with optional siren)
Double tap again to change setting.
Perimeter On: 2 Chirps
Perimeter Off: 3 Chirps
3.
Turn your ignition key off to save and exit program mode.
4.
Manually arming the Perimeter Sensor will not change the default. The next
time the system arms automatically, it will go back to the default setting.
(see Arming with Perimeter Sensor above)
Adjusting G sensor Sensitivity (Shock and Tilt Triggers)
The sensitivity is on a scale from 1-5 indicated by 1-5 chirps or turn
signal flashes with 5 being most sensitive.
(If equipped with optional siren)
1.
Manually disarm the alarm by double tapping the button.
2.
Turn your ignition key on-off-on and then hold the remote button. The siren will
chirp and turn signals will flash to let you know the current sensitivity level.
(Default is level 3)
3.
Press the button to change sensitivity.
4.
Turn ignition key off to save and exit. The siren will give 1 chirp to indicate the
save.
7
Note: If the perimeter sensor is armed for more than 10 days, the system will automatically
disable the perimeter sensor to conserve battery life.