Schweitzer Engineering SEL-3355-2 Getting Started Download Page 9

Page: 9 / 16

Date Code 20180212

Getting Started With the SEL-3355-2

Step 4. If any of the SATA drives that were ordered with the computer are not displayed, open the SATA

drive bay on the front panel of the SEL-3355-2 and verify that they are installed.

Step 5. If all drives are installed, turn off the SEL-3355-2. Then pull out and reinstall each drive one at a

time, ensuring that they are firmly inserted.

Step 6. Restore power to the SEL-3355-2 and verify that all drives are now present in the

Disk

Management

application.

If any of the drives are not present after performing this step, contact your customer service
representative for further assistance.

Hardware

Perform the following steps to verify that all the hardware is correctly installed in the SEL-3355-2:

Step 1. Click the

Start

button, type

device

in the box, and then select

Device Manager

Summary of Contents for SEL-3355-2

















Search results

Summary of Contents for SEL-3355-2

Reviews:

Related manuals for SEL-3355-2

Brands by name

Popular brands

Schweitzer Engineering SEL-3355-2, Getting Started

Search results

Summary of Contents for SEL-3355-2

Reviews:

Related manuals for SEL-3355-2

Brands by name

Popular brands