Schweitzer Engineering SEL-2032 Instruction Manual Download Page 62 | Manualshive

Page: 62 / 354

background image

2.16

SEL-2032

Communications Processor

Instruction Manual

Date Code 20120126

Installation

Getting Started

Step 8. Type

STATUS <Enter>

and verify that a status report similar

to the one in

appears on your terminal.

Verify the following from the report:

➢

RAM memory size is 512 kb.

➢

Shared-RAM size is 1024 kb.

➢

Flash (ARCH) is 1792 kb.

➢

IRIG-B input and I/O board match your configuration.

➢

Any plug-in protocol cards are displayed as expected
for Port 17 or 18.

*>>

STATUS <Enter>

COMMUNICATIONS PROCESSOR - S/N 95012004 Date: 10/31/01 Time: 13:46:43
FID



SEL-2032-R100-V0-Z000000-D20021222 FID



SLBT-2030-R103-V0-Z000000-D20010122

SELF-TESTS

RAM SRAM CODE ARCH EEPROM P.S. SET BATTERY
512 kb 1024 kb OK 1792 kb OK OK OK OK

IRIG-B Input: Absent
I/O Board: Absent

Port Status     Success Rate SET M Database
1 Active     100% None
2 Inactive     None
3 Inactive     None
4 Inactive     None
5 Inactive     None
6 Inactive     None
7 Inactive     None
8 Active     None
9 Active     None
10 Inactive     None
11 Inactive     None
12 Inactive     None
13 Inactive     None
14 Inactive     None
15 Inactive     None
16 Inactive     None
17 Sole Node(100h) NORM None
F Active     100% None

*>>

Figure 2.8

STATUS Command Screen

Collect Data With
the SEL-2032

Step 1. Connect the SEL-351S Relay to an SEL-2032 port; this

example uses Port 2.

Use either an SEL C272A or SEL C273A cable to connect the
relay to the SEL-2032.

If you are using an SEL C272A cable:

➢

Connect the end labeled SEL-300/500 series to Port 2
on the SEL-351S.

➢

Connect the other end of the cable to Port 2 on the
SEL-2032.

If you are using an SEL C273A cable:

➢

Connect the end labeled SEL-300/500 series w/IRIG to
Port 2 on the SEL-351S.

➢

Connect the other end of the cable to Port 2 on the
SEL-2032.

You can connect to any port on the SEL-351S that is configured
for the SEL protocol. The factory-default setting for the relay

Courtesy of NationalSwitchgear.com

«
...
60
61
62
63
64
...
»

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

PCMCIA WIRELESS ASAPTER DWL-650

Brand: D-Link Pages: 5

PowerLine DHP-W611AV

Brand: D-Link Pages: 78

Brand: LaCie Pages: 44

LaCie Ethernet Disk

Brand: LaCie Pages: 2

SATA II ExpressCard 34

Brand: LaCie Pages: 2

12big Rack Fibre 8

Brand: LaCie Pages: 9

ThunderLAN TNETE100A

Brand: Texas Instruments Pages: 179

Brand: Cypress Semiconductor Pages: 9

Brand: Digitus Pages: 8

InvenSense RoboKit1

Brand: TDK Pages: 13

Brand: Lindy Pages: 12

Brand: Altera Pages: 33

iMarc SLV 9820-2M

Brand: Paradyne Pages: 24

Brand: RR-Concepts Pages: 12

Brand: Omron Pages: 14

WAFER-EHL Series

Brand: IEI Technology Pages: 142

Brand: RadioSPECTRAL Pages: 2

Brand: ZALMAN Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands