Schweitzer Engineering SEL-2032 Instruction Manual Download Page 41 | Manualshive

Page: 41 / 354

background image

1.25

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Introduction and Specifications

Details

power. The lithium-type battery has an expected life of 10 years. The internal
clock is accurate to within 1 minute per year with power applied. You can
reset the clock and calendar using the SEL-2032

TIME

and

DATE

commands.

Distributes IRIG-B Through Ports 1–16

The SEL-2032 distributes a demodulated IRIG-B signal through all of its 16
rear ports. You can use this to synchronize any type of device, such as a relay,
fault recorder, or meter, that can decode the IRIG-B signal. To use this feature,
you need only to connect the device to the desired SEL-2032 port using a
special cable designed for both communication and IRIG-B signal. For
devices that do not have an IRIG-B port or cannot decode the IRIG-B signal,
the SEL-2032 can send time and date messages on a periodic or time basis to
keep their clocks synchronized.

Details

Settings

SET

command variations allow you to configure and control SEL-2032

operation. See

Section 7: Settings

for more detailed information about this

group of commands.

SET P—Port Configuration

You can use the SET P settings to establish each port’s configuration and
communication parameters. The configuration options are designed to make
the SEL-2032 compatible with almost any device that has an EIA-232 port.
This is the only setting command required to use the SEL-2032 as a port
switch.

You should use the

SET P

command to configure each port. The first prompt

from the SEL-2032 asks you to identify the type of device connected to the
port. Port F can only be configured as a Master port. Ports 17 and 18
correspond to the protocol cards and are set automatically to match the
installed card.

SET A—Auto-Message Settings

Use SET A settings to control the following automatic messaging settings:

➤

Initialization message to be sent to the IED when
communication begins

➤

Fast Operate message enable

➤

Outgoing messages for control and data collection

➤

Size of the User region

SET U—User-Defined Commands

Use the

SET U

command (Ports 1–16) to create user-defined commands that

other devices send to the SEL-2032. You can also use this setting to trigger
action from selected SEL relay auto-messages (Event, Status, and Group). The
user-defined commands can supplement or replace the preprogrammed

Courtesy of NationalSwitchgear.com

«
...
39
40
41
42
43
...
»

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

Brand: CAME Pages: 4

Avenue Express Control Panel

Brand: Ensemble Designs Pages: 19

Brand: Taiwan Commate Computer Inc. Pages: 29

Brand: Velopex Pages: 7

SUPERLOADER DLT MAGAZINE

Brand: Tandberg Data Pages: 6

PISO-725 Series

Brand: ICP DAS USA Pages: 8

D-NVR4108HS-4KS2/L

Brand: Dahua Pages: 33

Masterliquid ML240L RGB

Brand: Cooler Master Pages: 18

Brand: Alesis Pages: 11

Brand: NXP Semiconductors Pages: 1202

Internal All-in-One Digital Media Drive ULT31793

Brand: Ultra Products Pages: 1

NetStructure ZT 5085

Brand: Intel Pages: 106

Brand: SilverStone Pages: 12

SelectIO 7 Series

Brand: Xilinx Pages: 188

Brand: KE2 Therm Solutions Pages: 26

Maxeta iFA Series

Brand: TDK Pages: 18

ISA Bus Bi-Directional Parallel Port Board

Brand: Lava Pages: 1

Brand: Billion Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands