Schweitzer Engineering SEL-2032 Instruction Manual Download Page 116 | Manualshive

Page: 116 / 354

background image

5.2

SEL-2032

Communications Processor

Instruction Manual

Date Code 20120126

Message Strings

Special Sequences

printable character. These sequences always begin with a backslash (‘\’).

shows the format of the various special character sequences

available.

The following are examples of simple strings:

“Another device”

A literal string for “Another device”

“TRIG\nY\n”

String for

TRIG<Enter>Y<Enter>

“\002HI\\BOB\003”

String for

<STX>HI\BOB<ETX>

You can use the quote character to define the beginning and end of a string. If
you do not, the SEL-2032 will put the string in quotes anyway. The only
exception is for predefined strings discussed later in this section.

Special Sequences

The SEL-2032 is preprogrammed to interpret special sequences of characters
for special purposes. You can use these special character sequences in auto-
messages or user-defined commands to control the data that are referenced by
the message and to control the response initiated by the message. These
special sequences are particularly well suited for use with non-SEL IEDs and
devices.

Message
Sequences

You may use the special character sequences listed in

in automatic

messages, configured with SET A, and special-purpose user-defined
command responses, configured with SET U.

Table 5.1

Special Characters for Use in Strings

Character

Comments

\”

The SEL-2032 interprets this as a quote character in a
string, as distinguished from quotes at the beginning and end of a string.

\\

The SEL-2032 interprets this as a backslash character in a string.

\n

<Enter>

sequence (CR/LF combination, just CR on SEL IED ports).

\0xx

The SEL-2032 interprets this as an 8-bit character, where xx = an ASCII
character value in hexadecimal; (e.g., \004 is ASCII End-of-Text, EOT,
character). See

Appendix E: ASCII Reference Table

for a conversion table.

\ <Enter>

Use to continue a string to the next line.

Table 5.2

Special Message Sequences for Strings

(Sheet 1 of 3)

Character

Comments

\CS

x

/

Begin checksum calculation.

x

specifies checksum type.

c = CRC-16. Based on the polynomial X

16

+ X

15

+ X

2

+ 1

b = 8-bit checksum. Sum all
bytes and take least significant byte.
w = 16-bit checksum. Sum all bytes and take two-byte result.

\CE/

Stop checksum calculation.

Courtesy of NationalSwitchgear.com

«
...
114
115
116
117
118
...
»

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

Brand: TC Electronic Pages: 2

Brand: EAW Pages: 10

Brand: dbx Pages: 2

Brand: IEI Technology Pages: 21

ThunderLAN TNETE100A

Brand: Texas Instruments Pages: 179

Brand: ROE Pages: 41

Brand: HARTING Pages: 13

Brand: TANDBERG Pages: 3

Duinotech Lilypad Plus XC3920

Brand: Jaycar Electronics Pages: 2

4 Channel Input Buffer Board SDAIBB

Brand: B&B Electronics Pages: 22

PowerBeam PBE-5AC-400-ISO

Brand: Ubiquiti Pages: 23

Brand: AMX Pages: 1

Brand: ANEP Pages: 48

Brand: VideoWave Pages: 12

BiPAC 5200S RC Series

Brand: Billion Pages: 79

Brand: A.E.B. Pages: 28

HiGain Line Unit HLU-388

Brand: PairGain Pages: 7

Brand: Cypress Semiconductor Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands