Schweitzer Engineering Laboratories SEL-351 Instruction Manual Download | Manualshive

Page: 603 / 614

background image

Date Code 20001006

M

IRRORED

B

ITS

™

I-1

SEL-351 Instruction Manual

APPENDIX I: MIRRORED BITS™ (IN FIRMWARE VERSIONS

1 TO 4)

O

VERVIEW

M

IRRORED

B

ITS

is a direct relay-to-relay communications protocol which allows protective relays

to exchange information quickly and securely, and with minimal expense. The information
exchanged can facilitate remote control, remote sensing, or communications-assisted protection
schemes such as POTT, DCB, etc. The SEL-351 supports two M

IRRORED

B

ITS

channels,

differentiated by the channel specifiers A and B. Bits transmitted are called TMB1x through
TMB8x, where x is the channel specifier (e.g., A or B), and are controlled by the corresponding
SEL

OGIC

Control Equations. Bits received are called RMB1x through RMB8x and are usable as

inputs to any SEL

OGIC

Control Equations. Channel status bits are called ROKx, RBADx,

CBADx and LBOKx and are also usable as inputs to any SEL

OGIC

Control Equations. Further

channel status information is available via the COM command.

Important:

Do not connect an unconfigured port to a M

IRRORED

B

ITS

device. Otherwise the

relay will appear to be locked up. Configure the port first, then connect the device.

O

PERATION

Message Transmission

All messages are transmitted without idle bits between characters. Idle bits are allowed between
messages.

•

At 4800 baud, one message is transmitted each 1/2 power system cycle.

•

At 9600 baud, one message is transmitted each 1/4 power system cycle.

•

At 19200 and 38400 baud, one message is transmitted each 1/8 power system cycle for
the SEL-321 and 1/4 power system cycle for the SEL-351.

Message Decoding and Integrity Checks

The relay will deassert a user-accessible flag per channel (hereafter called ROKx) upon failing any
of the following received-data checks:

•

Parity, framing, or overrun errors.

•

Receive data redundancy error.

•

Receive message identification error.

•

No message received in the time three messages have been sent.

Courtesy of NationalSwitchgear.com

«
...
601
602
603
604
605
...
»

Summary of Contents for SEL-351







































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-351

Brand: Seg Pages: 36

REVEX 2PH RX2 280 Series

Brand: CD Automation Pages: 59

Brand: GE Pages: 16

Brand: GE Pages: 32

Brand: GE Pages: 16

Brand: GE Pages: 36

Brand: GE Pages: 50

Brand: GE Pages: 560

Brand: GE Pages: 2

MELPRO MGR-A3t-R

Brand: Mitsubishi Electric Pages: 21

Brand: Mitsubishi Electric Pages: 40

MELPRO MVG-A3V-R

Brand: Mitsubishi Electric Pages: 18

MELPRO MOC-A3T-R

Brand: Mitsubishi Electric Pages: 23

MELPRO MDG-A4V-R

Brand: Mitsubishi Electric Pages: 19

MELPRO CBV2 -A02S1

Brand: Mitsubishi Electric Pages: 48

MELPRO MOV-A3V-R

Brand: Mitsubishi Electric Pages: 16

MELPRO MDG-A3V-R

Brand: Mitsubishi Electric Pages: 22

Brand: steute Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands