manualshive.com logo in svg

Schweigen Isodrive 3200, Installation Manual

Share
Download
Schweigen Isodrive 3200 Installation Manual Download Page 20

Page 20

6. SteelFlex

™

 Safety Duct

Securing SteelFlex

™

 Safety Duct

SteelFlex

™

 safety duct must be installed with supports at maximum intervals of 1.5 metres. SteelFlex

™

 safety 

ductwork can be supported by using good quality gaffer or aluminium foil tape. Provided that it does not 
restrict the internal diameter of the ducting. Ducting installed looped over hanging beams should be installed 
in such a manner as to ensure the changes of direction are gradual. Support of the ducting with the use of 
hangers may be required, see option 2. 

NOTE:

 Ducting should be kept taut at all times.

Figure 7 Examples of securing ducting

Option 1

Secure the SteelFlex

™

 

duct to the beam

Option 2

Support SteelFlex

™

 

duct by using hangers.

NOTE:

 Care shall be 

taken to minimize 
sagging or snaking 
of the duct between 
supports.

Aluminium foil 

tape

Aluminium foil tape

Hanger

250mm SteelFlex

™

 ducting,  

DO NOT

 reduce ducting size.

Summary of Contents for Isodrive 3200





























Reviews:

No comments

Brands by name

Popular brands

Load more brands