USER MANUAL ZHS21
MOTION DETECTOR
ZHS21
MANUFACTURER INFORMATION
Dear Customer,
should you require technical advice and
your retailer could not help please contact
our technical support.
Schwaiger GmbH
Würzburger Straße 17
90579 Langenzenn
Hotline: +49 (0) 9101 702-199
www.schwaiger.de
3. Networking button
Press the networking button (within the hole)
for 2 seconds until the green LED starts to flash
fast, then let go. The device will be detected
and included into the network.
4. Installation of the motion detector
Select a place for installation. Remove the pro-
tective cover and stick the bracket to the place
desired.
Congratulations and thank you for purchasing the Schwaiger
ZHS21 product. Below you will find useful operating guidelines.
Network inclusion of the motion detector
Put the Gateway into inclusion mode.
Remove the protective battery cover, press the networking button for 2
seconds until the green LED starts to flash fast.
5. Attach the motion detector
to the bracket
This is a smart motion detector which is based on the ZigBee Wireless Networking tech-
nology. It has a very low power consumption which makes for longer battery life. The
motion detector is only suitable for indoor use. Upon choosing a place for installation
of the detector, please make sure that the device is not exposed to extreme changes in
temperature (e.g. near a radiator) and that there are no constantly moving objects (e.g.
ceiling fan) in close proximity to the motion detector.
Network inclusion
1. Remove the protective battery cover.
The red LED will then glow. The device can be used
as soon as the red LED is off.
This takes up to 30 seconds.
2. Put the Gateway into inclusion mode
Bitte achten Sie darauf, dass bei der Einbuchung des Bewegungsmelders
der Abstand zwischen dem Gateway und dem Sensor nicht mehr als 0,5 m
beträgt.
6. Network removal of the device
Put the Gateway into removal mode by
choosing „Home setup“ in the main menu
and then click on „Add device“ (See images
on the left). Then reset the device to default
settings.
7. Reset to default settings
Press the networking button for 5 seconds
until the LED starts to flash slowly.
Note: For network inclusion, the sensor must
always be in the factory state
LED indicator of devices
Network inclusion
Press the networking button for 2
seconds until the green LED starts to flash
(two times per second)
Network removal / Reset
The LED flashes 6 times
(once per second)
Alarm (anti-tamper key)
The red LED flashes once
Technical data
Working voltage
DC 3 V (1xCR123A battery)
Static curren
≤ 15 µA
Alarm current
≤ 30 mA
Detecting angle
90°
Installation height
2.1 m
Detecting distance
8 - 10 m
Working environment
-10°C ~ +50°C
Transmission power
<1 mW
Frequency range
2405-2480 MHz
Range
about 15 m (depending on building
structure)
Dimension
65 x 65 x 28.5 mm
Read these instructions before installing!
Do not use the device in any manner other than that specified in the manual. The
manufacturer disclaims any guarantee if the device is used improperly.
CAUTION!
The device is not a toy. Keep away from children and pets. The device cannot be repaired
and must not be opened.
Disposal
Do not dispose of batteries or electric and electronic devices in the normal house-
hold waste. The consumer is legally obliged to return electrical and electronic de-
vices and batteries that are at the end of their useful life to the point of sale or
public collection points that have been set up for this purpose. Legislation in the
country of use governs individual details regarding disposal. batteries should be disposed
of separately. The symbol on the product, the user guide or the packaging indicates this
legal requirement.
Declaration of conformity
Schwaiger GmbH hereby declares that the specified radio equipment product complies
with Directive 2014/53/EU and other applicable directives. The complete EU declaration
of conformity is available online at: http://konform.schwaiger.de
Explanation of symbols
CAUTION!
This symbol indicates a danger.
NOTE:
This symbol indicates important points.
plan view
announce-
ment
Sensor
side view
mounting
BDA_ZHS21_b