SCHURR SCHURR cow-brush type B00 Operating Instructions Manual Download Page 20 | Manualshive

Page: 20 / 27

SCHURR SCHURR cow-brush type B00 Operating Instructions Manual Download Page 20

SCHURR cow-brush Type B00/C12

Feb. 2017 Page 20 www.schurr-geraetebau.de

5.3.5 Power supply

Danger!

Electric voltage or current.

Can lead to serious injury or death.

Ensure that work with live parts and electrical connection is performed by a qualified and

authorised electrician only.



A qualified electrician should connect the power supply with the connecting terminal/ground clamp.



Protection max. 16A. It has to be a residual current circuit-breaker installed.

The qualified electrician have to connect the protective conductor (green/yellow)

5.4 First time use

5.4.1 Measures prior to first time use

A qualified electrician should



Set the potentiometer in the control housing to the required time (preset to approx. 18 sec.).

5.4.2 Trial run

When the device has been connected to the power supply, the functionality may be tested.

Sequence of actions

Typ C12/B00:



Turn the brush to start the motor accordingly. It’s not necessary to push the support frame

upwards!

«
...
18
19
20
21
22
...
»

Summary of Contents for SCHURR cow-brush type B00




























Reviews:

No comments