4
1.
Position AC power cord and DC charging cords to reduce
risk of damage by hood, door, or moving engine parts.
2.
Stay clear of fan blades, belts, pulleys, and other parts that
can cause injury.
3.
Check polarity of battery posts. Battery case will be marked
by each post:
POSITIVE (POS, P, +) and NEGATIVE (NEG,
N, -). NOTE:
The positive battery post usually has a larger
diameter than the negative post.
4.
Determine which post of battery is ground (connected) to
chassis.
NOTE:
The negative post is normally grounded.
NEGATIVE GROUNDED POST
5A. For negative-grounded vehicle, connect POSITIVE (RED)
clip from battery charger to POSITIVE (POS, P, +)
ungrounded post of battery. Connect NEGATIVE (BLACK)
clip to vehicle chassis or engine block away from battery.
Connect to a heavy gauge metal part of the frame or engine
block.
POSITIVE GROUNDED POST
5B. For positive-grounded vehicle, connect NEGATIVE (BLACK)
clip from battery charger to NEGATIVE (NEG, N, -)
ungrounded post of battery. Connect POSITIVE (RED) clip
to vehicle chassis or engine block away from battery.
Connect to a heavy gauge metal part of the frame or engine
block.
1.
Check polarity of battery posts. Battery case will be marked
by each post: POSITIVE (POS, P, +) and NEGATIVE (NEG,
N, -).
NOTE:
The positive battery post usually has a larger
diameter than the negative post.
2.
Attach a 24-inch long (or longer) 6-gauge (AWG) insulated
battery cable to NEGATIVE (NEG, N, -) battery post.
3.
Connect POSITIVE (RED) charger clip to POSITIVE (POS,
P, +) post battery. Rock clip back and forth to make good
connection.
4.
Position yourself and free end of 24 inch cable as far away
from battery as possible. Then connect NEGATIVE (BLACK)
charger clip to free end of cable.
WARNING:
Do not face battery when making final
connection. Rock clip back and forth to make a good
connection.
5.
Make all desired settings before applying AC power to the
charger.
6.
Observe the meter for proper response, if something does
not look right, refer to the troubleshooting section of this
manual.
7.
When battery is fully charged, unplug charger from AC power
source.
When charging battery out of vehicle, take care to determine the battery type. To reduce risk of a spark near battery, follow these steps
when battery is outside vehicle.
WARNING:
A spark near the battery may cause battery explosion.
WARNING:
When removing battery
from vehicle or boat, disconnect grounded pole first. When disconnecting, make sure all accessories are off, so as not to cause an arc.
(
NOTE:
A marine (boat) battery must be removed and charged on shore. (To charge on board requires special equipment designed for
marine use.)
WARNING:
When reinstalling battery, attach the ground post first.
8.
When battery is fully charged and charger is unplugged,
(1) remove clip from end of Negative end of cable, and
(2) remove clip from Positive battery post, in that order.
9.
Clean and store battery charger.
WARNING: Be sure area around battery is well ventilated
while battery is being charged.
Gas can be forcefully blown
away by using a piece of cardboard or other non-metallic mate-
rial as a fan.
NEGATIVE
BATTERY
POSITIVE
+
-
24", 6 GUAGE
CABLE
TO GROUNDED
POWER OUTLET
CONNECT NEGATIVE BATTERY
CLIP TO 24 INCH CABLE END
BATTERY CHARGER
POWER CORD
E.
OPERATING INSTRUCTIONS: CHARGING BATTERY IN VEHICLE
When charging battery in the vehicle, take care to determine the battery type and which post is grounded. To reduce risk of a spark near
battery, follow these steps when battery is installed in vehicle.
WARNING: A spark near battery may cause battery explosion.
WARNING:
Do not connect clip to carburetor, fuel lines, or sheet-
metal body parts.
NOTE:
Attach clips to battery post and twist
or rock back and forth several times to make a good connec-
tion. This tends to keep clips from slipping off terminals and
helps to reduce risk of sparking.
6.
Make all desired settings before applying AC power to the
charger.
7.
Observe the meter for proper response, if something does
not look right, refer to the trouble shooting section of this
manual.
8.
When battery is fully charged, unplug charger from AC outlet.
9.
Remove charger clips from (1) chassis and (2) battery post,
in that order.
F.
OPERATING INSTRUCTIONS: CHARGING BATTERY OUT OF VEHICLE