Schmidt SS 20.200 Instructions For Use Manual Download Page 2 | Manualshive

Page: 2 / 12

Schmidt SS 20.200 Instructions For Use Manual Download Page 2

Instructions for Use SS 20.200

Page 2

SCHMIDT

®

Flow Switch

SS 20.200

Table of Contents

1

Important information....................................................................... 3

2

Application range ............................................................................. 3

3

Mounting instructions....................................................................... 4

4

Electrical connection........................................................................ 6

5

Commissioning ................................................................................ 7

6

Switching threshold ......................................................................... 8

7

Service information .......................................................................... 9

8

Technical data ............................................................................... 10

9

Certificate of conformity ................................................................. 11

Imprint:

Copyright 2016

SCHMIDT Technology

All rights reserved.

Version: 505518.01C

Subject to modifications

«
1
2
3
4
...
»

Summary of Contents for SS 20.200













Reviews:

No comments