Schmidt DT Series Operating Instructions Manual Download Page 13 | Manualshive

Page: 13 / 16

background image

13

3.5 Memory

(Cont.)

4. Press

to go back to normal operation.

The above settings can be checked quickly by performing steps A to C as described

above and then pressing

.

3.6 Troubleshooting

RPM reading is displayed but unit is not flashing

:

• Flash tube may need to be replaced (see „Flash Tube Replacement“ section)

Stroboscope is in external signal mode, no flash

:

• Check flash tube. Replace if necessary
•

Check for damaged wiring and/or loose pin connections

Stroboscope is in internal signal mode, no flash

:

• Check flash tube. Replace if necessary
• Check for damaged wiring and/or loose pin connections

«
...
11
12
13
14
15
...
»

Summary of Contents for DT Series

















Reviews:

No comments

Related manuals for DT Series

Coronis 5MP Mammo

Brand: Barco Pages: 4

Brand: Barco Pages: 167

Color Coronis 2MP

Brand: Barco Pages: 156

Color Coronis 2MP

Brand: Barco Pages: 12

Brand: Barco Pages: 39

Brand: Barco Pages: 158

Brand: Federal Signal Corporation Pages: 2

Brand: Harman Kardon Pages: 7

Brand: ParaBody Pages: 5

Brand: olympia electronics Pages: 4

Brand: Olympus Pages: 56

Brand: Magicfx Pages: 25

Brand: Valmont Structures Pages: 8

Brand: Gilson Pages: 8

CHIEFTAIN E1006

Brand: Falcon Pages: 5

Brand: Hoist Fitness Pages: 17

Brand: Peak Pilates Pages: 4

Brand: Toro Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands