background image

15

SLC440COM Series

SLG440COM Series

Operating instructions

Safety light curtain / safety light grid

EN

RED-Directive 2014/53/EU

This device complies with Part 15 of the FCC Rules Operation is subject to 
the following two conditions: 
(1) this device may not cause harmful interference, and 
(2) this device must accept any interference received, including interference 
that may cause undesired operation
This equipment has been tested and found to comply with the limits for a 
Class B digital device, pursuant to Part 15 of the FCC Rules These limits 
are designed to provide reasonable protection against harmful interference 
in a residential installation This equipment generates, uses, and can radiate 
radio frequency energy and, if not installed and used in accordance with 
the instructions, may cause harmful interference to radio communications 
However, there is no guarantee that interference will not occur in a particular 
installation

Contains transmitter 
module
IC: 12246A-BM71S2

This Class B digital apparatus complies with Canadian ICES-003
This device complies with Industry Canada’s license-exempt RSS 
standard(s) Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may 
cause undesired operation of the device

Cet appareil numérique de la classe B est conforme à la norme NBM-003 
du Canada Le présent appareil est conforme aux CNR d'Industrie Canada 
applicables aux appareils radio exempts de licence L'exploitation est 
autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, 
même si le brouillage est susceptible d'en compromettre le fonctionnement

Este equipamento não tem direito à proteção contra interferência prejudicial 
e não pode causar interferência em sistemas devidamente autorizados
This equipment has no right to be protected against harmful interference and 
may not cause interference to duly authorized systems

KCC (Korean Communications Commission) EMC certification mark 
Includes adjacent KCC certification number: MSIP-CRM-mcp-BM71BLES1FC2

April 5, 2020

Information on wireless interface

9.2  Information on wireless interface

Summary of Contents for SLC440COM Series

















Reviews: