schmersal EX-T 335 Operating Instructions Manual Download Page 3

3

EX-T 335

Operating instructions

Position switches

EN

3.  Mounting

3.1  General mounting instructions

Fitting is only authorised in a de-energised condition

The enclosure can be fixed by means of 4 mounting holes. The 

mounting dimensions are mentioned at the rear of the enclosure. The 

fixing screws must be protected against unauthorised tampering. The 

use of a protective ground wire is imperative. The enclosure must not 

be used as an end stop. Any mounting position.

To ensure a proper functioning, the switch must be installed so that 

the required switch travel is obtained. For safety functions, at least the 

positive break travel indicated in the switch travel diagram (refer to 

catalogue) must be obtained. All components have sufficient after-

travel to compensate for inaccuracies in the guidance of the actuating 

system. The actuation of the switch beyond its end stop however must 

be avoided.

Please observe the recommendations regarding maximum 

impact energy, actuating speed and tightening torque in the 

technical data.

Please observe the relevant requirements of the standards 

ISO 12100, ISO 14119 and ISO 14120.

3.2  Dimensions

All measurements in mm.

76

40,5

30

7,3

5,3

60

66,5

30,5

6

M20

17

38

9,5

18

3.3  Settings

Changing the switching function (4VH, 4V7H, 4V10H)

Position switches with "4V" actuating head can be set so that they 

are switched either only clockwise, only counterclockwise or in both 

directions. The following steps are required:

1. Unscrew the retaining screws and remove the actuating head

2. Change the position of both inner plastic parts

3.  Replace the actuating head and tighten the screws

4. Tightening torque for the head screws: 1.5 Nm

Changing the switching function

switching in both directions

switching only clockwise

switching only counterclockwise

Summary of Contents for EX-T 335







Reviews: