4
GB
INITIATION
<< The machine may not be operated by
more than one person at any given time!
The machine was designed for safe
operation by “one person only”.
<< During the shredding process no other
work may be performed on the machine
(for example cleaning, etc.).
<< Keep children away from the machine.
This machine’s design and safety concept
are based on adult dimensions (feeder
route, safety cut-off switches, etc.) to
ensure that it can be operated safely by
adults only.
<< Repairs may only be performed by
trained personnel.
<< Keep all loose articles of
clothing, ties, jewelery,
long hair or other loose
objects away from
opening, injury may
result!
<< Never insert fingers into opening.
Serious injury may result!
<< In case of danger switch the
machine off with the mains switch,
or with the emergency switch, or
unplug the machine.
<< Always unplug the machine from
the mains power supply before
opening the machine.
STOP
IMPORTANT SAFETY NOTES
APPLICATION:
The INTIMUS 852VS shredder is used in all areas
where large quantities of printed material need to
be shredded.
The machine can shred cardboard and crumpled
paper as easily as it shreds smooth paper.
CAUTION: The shredder should only
be fed with paper or cardboard!
Shredding other data carriers can cause
injury(e.g. by splintering of hard materials)
or may damage the shredder (e.g.
destruction of the cutting system).
INSTALLATION REQUIREMENTS:
- Unpack and set machine upright.
- Put the collecting bag into the sliding frame (see
description „EMPTYING THE COLLECTING
BAG“)
- Plug in the machine (see TECHNICAL DATA for
information concerning required pre-fusing of
the electrical outlet).
The air vents in the housing are
necessary for cooling and may not be
covered or closed!
The mains connection at the machine
must be freely accessible!
Only operate the machine in enclosed
rooms at temperatures between 10
°
C
and 40
°
C!
MALFUNCTION
TAKING OUT EXCESS PAPER
IN CASE OF OVERLOAD:
If the shredder has stopped due to an overload
(motor protection) take the excess paper out of
the inlet as follows:
- Depress the reverse pushbutton (4) (fig. 2). The
material is released.
- Lift up the hopper. The pilot lamp „door open“ or
„hopper open“ (7) (fig. 2) will light.
- Remove the excess material by hand from the
inlet guide.
Note: In this case, there is no danger of injury as
all circuits are interrupted when the hopper is
lifted and the machine cannot be started.
MOTOR FAULT:
The machine is equipped with a thermally protected
motor. Should this motor be overloaded, it will
switch off automatically. In such case the pilot
lamp „ready“ (5) (fig. 2) flashes.
After a cooling down period of approx. 10 minutes
(depending on the room temperature) you can
restart the machine and continue shredding.
Note: When the motor is overloaded, only the
forward run is cut off. To take the excess paper out
of the inlet opening, the cutting system may at any
time be switched on „reverse“.
FAULT CHECKLIST:
If the machine is not functioning properly, you
should check the following:
- is the plug conneted to the mains?
- is the mains switch (1) turned on?
- is the door closed?
- is the collecting bag full?
The bag has to be emptied.
- is the motor overloaded?
Please refer to the section headed „Motor Fault“.
If none of the above applies, please contact
your dealer.
TECHNICAL DATA
Cutting width:
3.8x40 mm (cross-cut)
Cutting capacity:
60-70 sheets (70 g/m
2
)
Cutting speed:
0.04-0.36 m/sec.
Working width:
444 mm
Power:
2,3-2,9 kW
Supply voltage:
220-240V/50-60Hz
Pre-fusing:
16 A
Width:
750 mm
Depht:
550 mm
Height:
1600 mm
Noise level:
approx. 75 dB(A)
Weight:
approx. 201 kg
ACCESSORIES
Description
Order-No.
Plastic bag,
600x380x1100x0,06 mm
80946
Lubrication bottle, 125 ml
99943
Note: For orders of special accessories and
spare parts, please contact your dealer.
MAINTENANCE
CLEANING THE PHOTOCELLS (Fig. 3):
If paper particles should come to rest in the inlet
guide (for example after a paper jam) it is possible
that the machine will not turn off, due to the broken
light barrier.
To remove these paper strips and also to clean
the photocell, pass another sheet of paper through
the feed slot, or switch the machine to reverse and
wipe both „eyes“ of the photocell with a brush.
CUTTING SYSTEM MAINTANANCE:
After about 2 hours of continuous operation
run the cutting system in reverse for about 30
seconds and, at the same time, spray some of the
enclosed special oil onto the cutting system.
ENERGY SAVING TIP:
Be certain that the machine is turned off overnight
(mains switch (1) (fig. 1) switched to „0“).
11
fig. 3
Schleicher International
852VS
1-800-658-8788 - www.abcoffice.com
