manualshive.com logo in svg

Schlage KC9232, Installation Manual

Share
Download
Schlage KC9232 Installation Manual Download Page 19

KC9232/KC9232-2 & KC9233/KC9233-2 INSTALLATION

Testing the KC9232/KC9232-2 or KC9233/KC9233-2

57041-D                                              Page 19                                              04-11-2007

Testing the KC9232/KC9232-2 or KC9233/KC9233-2

Testing:

1.  Knob should rotate freely.

2.  Insert key into cylinder and rotate knob in direction required to retract latch.

>   Direction of knob rotation depends on door hand - if it doesn’t work in one direction, try 

the other.

>   You should be able to lock and unlock the deadbolt.

>   For 4710 deadlatches, you should be able to retract the latch.

3.  Rotate key back to original position and remove it.

>   Knob should rotate freely and not retract the deadbolt/latch.

4.  Using the keypad, enter the default access code: 1  3  5  7  9.

>   The red LED should light each time the first four numbers are pressed and when the 9 is 

pressed, the green LED should flash for five seconds.

>   While the green light is flashing, the knob should be engaged and you should be able to 

lock or unlock the deadlatch.

5.  Test inside cylinder or thumbturn (for 4710/4730/8400 models: paddle/exit device, etc.) to insure that 

it is operating properly.

SEE PROGRAMMING GUIDE FOR PROGRAMMING INFORMATION.

Summary of Contents for KC9232





















Reviews:

No comments

Brands by name

Popular brands

Load more brands