background image

5

ROTARY

MOWER

S AF ETY

N OTI C E  ! ! !

Unauthorized modifications may present 

e x t r e m e

 

safety hazards to operators and bystanders and 
could also result in product damage.  

Schiller Grounds Care, Inc. strongly warns against, 

rejects  and  disclaims  any  modifications,  add-on 

accessories or product alterations that are not 
designed, developed, tested and approved by Schiller 
Grounds Care, Inc. Engineering Department.  Any 
Schiller Grounds Care, Inc. product that is altered, 

modified or changed in any manner not specifically 

authorized after original manufacture–including the 
addition of “after-market” accessories or component 

parts  not  specifically  approved  by  CGC,  Inc.

–will 

result in the Schiller Grounds Care, Inc. Warranty 
being voided.

Any and all liability for personal injury and/or 
property damage caused by any unauthorized 

modifications, add-on accessories or products not 

approved by Schiller Grounds Care, Inc. will be 
considered the responsibility of the individual(s) or 
company designing and/or making such changes.  
Schiller Grounds Care, Inc. will vigorously pursue 
full indemnification and costs from any party 
responsible for such unauthorized post-manufacture 

modifications and/or accessories should personal 

injury and/or property damage result.

 

This symbol means:

 

ATTEN TI ON !  

 

B EC OME  AL ERT!

 

 

Your safety and the safety of others is involved.

Signal word definitions

:

The signal words below are used to identify levels 
of hazard seriousness. These words appear in this 
manual and on the safety labels attached to Schiller 
Grounds Care, Inc.machines. For your safety and 
the safety of others, read and follow the information 
given with these signal words and/or the symbol 
shown above.

 

D AN G ER 

indicates an imminently hazardous 

situation which, if not avoided, 

WI L L  

result in death 

or serious injury. 

 

WARN I N G  

indicates a potentially hazardous 

situation which, if not avoided, 

C OU L D  

result in 

death or serious injury. 

 

C AU TI ON

 indicates a potentially hazardous situation 

which, if not avoided, 

MAY 

result in minor or moderate 

injury. It may also be used to alert against unsafe 
practices or property damage.

C AU TI ON  

used without the safety alert symbol 

indicates a potentially hazardous situation which, if 
not avoided, 

MAY

 result in property damage

MOD EL   N U MB ER:

  This number appears on 

sales literature, technical manuals and price lists.

S ERI AL   N U MB ER:  

 This number appears only 

on your unit. It contains the model number fol-
lowed consecutively by the serial number.  Use 
this number when ordering parts or seeking war-
ranty information.

Summary of Contents for Steiner 75-70855A







































Reviews: