www.scheppach.com /
+(49)-08223-4002-99 /
+(49)-08223-4002-58
GB | 31
In doing so, take into account the complete working
process, including the times when the electric tool is
working without load or switched off. Suitable meas
-
ures include regular maintenance and care of the
electric tool and the insertion tools, regular breaks as
well as proper planning of the working process.
7.
Before putting into operation
•
Open the packaging and remove the device carefully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
•
Check that the delivery is complete.
•
Check the device and accessory parts for trans -
port damage.
•
If possible, store the packaging until the warranty
period has expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plas
-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!
•
The machine must be securely installed, i.e. bolted
down on a workbench, base frame or similar.
• Before the machine is put into operation, all covers
and safety devices must be properly attached.
•
The saw blade must be able to move freely.
•
In the case of wood which has already been worked
with, check for foreign bodies such as nails or
screws etc.
•
Before pressing the on/off switch, make sure that
the saw blade is correctly attached and that moving
parts are free-running.
• Before connecting the machine, check that the data
on the type plate matches those of the mains system.
•
The machine must only be connected to a properly
installed safety socket which is protected by a fuse
of at least 16A.
8. Assembly
m
Warning! Risk of injury!
Improper installation of the circular table saw may re
-
sult in serious injury.
Before commissioning, properly and completely in
-
stall the circular table saw, including all covers and
safety devices.
Never plug the mains plug into the power outlet be-
fore completing the installation.
If connections are secured with a hexagon screw, nut,
spring washer and washer, the washer and spring
washer must be fitted under the hexagon screw. The
spring washer always lies directly on the (inner) hex
-
agon screw or nut.
6. Technical data
AC motor
230 V~ 50Hz
Power
2000 Watt
Operating mode
S1 & S6 40% *
Idling speed
4800 min
-1
Carbide saw blade
ø 254 x ø 30 x 2,8 mm
Number of teeth
24
Thickness riving knive
2,5 mm
Min. workpiece size
W x L x H
10 x 50 x 1 mm
Table size
546 x 630 mm
Cutting height max. 90°
87 mm
Cutting height max. 45°
55 mm
Height adjustment
0 - 87 mm
Saw blade, swivelling
0 - 45°
Extraction connection
ø 40 mm
Weight ca.
21/22 kg
* Operating mode S6 40%: Continuous operation with
intermittent load (cycle time 10 min). In order not to
heat the motor more than permitted, the motor may
only be operated for 40% of the cycle time with the
stated nominal power and must then continue run-
ning for 60% of the cycle time without a load.
Noise emission values
Sound values were measured in accordance with EN
62841.
Sound pressure level L
pA
93,5 dB(A)
Uncertainty K
pA
3 dB
Sound power level L
WA
106,5 dB(A)
Uncertainty K
WA
3 dB
Wear hearing protection.
The effects of noise can cause a loss of hearing. Total
vibration values (vector sum of three directions) de-
termined according to EN 62841.
NOTE:
The specified device emissions values have
been measured in accordance with a standardised
test procedure and can be used for comparison of
one electric tool with another.
The specified device emissions values can also be
used for an initial estimation of the load.
m
WARNING:
The noise emission values can vary
from the specified values during the actual use of the
electric tool, depending on the type and the manner
in which the electric tool is used, and in particular
the type of workpiece being processed.
Implement
measures to protect against noise nuisance.
