Scheppach 383484 2107, Operating And Safety Instructions Manual

Page: 18 / 46

16 GB/IE/NI
Keep the noise emissions and vibrations to a minimum!
• Only use appliances which are in perfect working order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.
9. Unpacking
• Open the packaging and remove the device carefully.
• Remove the packaging material as well as the packaging
and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport damage.
• If possible, store the packaging until the warranty period has
expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
10. Before Putting the Machine into Op-
eration
Correctly using the device
• The high-pressure cleaner must be set on a level, stable sur-
face.
• It is recommended that you maintain the correct operating
position every time you use the machine by placing one
hand on the pistol and the other on the lance.
• Never direct the water jet toward electrical lines or the ma-
chine itself.
• It is normal for the pump to leak a little; this is necessary to
avoid damage to the pump when it is at a standstill.
• Never use the equipment in potentially explosive areas un-
der any circumstances!
• The operating temperature must be b5 and +
50°C. Do not cover or modify the lance or the spray noz-
zles in any way.
• The high-pressure cleaner is designed to be used with cold
or lukewarm water (max. 50°C); higher temperatures can
damage the pump.
• Do not use water that is dirty, gritty or contains any chemical
products, as these could impair operation and shorten the
life of the equipment.
Assembly
Device assembly (fig. 4)
Push the handle (1) onto the fastening points at the top of the
device and secure using the two screws provided (length 20 mm)
Water supply connection (fig. 2)
Screw the connection for the water supply (10) onto the de-
vice. The connection for the water supply (10) features a con-
nection for standard hose coupling systems. Attach the hose
coupling of the supply hose (min. Ø 1/2“/ approx. 13 mm)
onto the connection for the water supply (10).
Always use an enhanced water hose with an industry-standard
coupling for the water supply. The length should be at least 6.0
m (not included in the scope of delivery).
A backflow prevention device must be installed between the
drinking water and the high-pressure cleaner! Ask your plumb-
ing expert about this.
Suction from open tanks/containers and natural
bodies of water
Use a special self-suction accessory (not included with delivery
/ available from dealer).
With this accessory, the high-pressure cleaner can take in wa-
ter 0.5 m above the water level. This can last about 25 to 50
seconds.
Immerse the accessory’s hose completely under water to drive
the air out of the hose.
Connect the accessory’s hose to the high-pressure cleaner, and
make sure that the suction strainer remains under water.
Let the high-pressure cleaner run with the spray gun removed
until the water flows evenly out of the high-pressure hose. If no
water comes out after 25 to 50 seconds, switch off and check
all connections.
Once the water is flowing, turn off the high-pressure cleaner
and connect the spray gun and spray lance to start work.
High-pressure hose connection (fig. 3/4)
Connect the high-pressure hose (2) to the connection for the
high-pressure hose (6). Remove the protective cover first.
Insert the other end of the high-pressure hose (2) into the pistol
connection (12).
To remove the high-pressure hose (3), press the button Taste
(A) and pull it out.
Connecting the attachments (fig. 5)
To mount attachments 13, 16, press them into the pistol (12)
and turn them until the lock.
To mount attachments 14, 15, 17, 18 insert these into the at-
tachment (13) and turn them until they lock.
11. Electrical connections
The electrical motor installed is connected and
ready for operation. The connection complies with
the applicable VDE and DIN provisions. The cus-
tomer‘s mains connection as well as the extension
cable used must also comply with these regula-
tions.
Damaged electrical connection cable
The insulation on electrical connection cables is often dam-
aged.
This may have the following causes:
• Passage points, where connection cables are passed through
windows or doors.
• Kinks where the connection cable has been improperly fas-
tened or routed.
• Places where the connection cables have been cut due to
being driven over.
• Insulation damage due to being ripped out of the wall outlet.
• Cracks due to the insulation ageing.