background image

 

 

 

– MOUNTING AND INSTALLATION 

COD: 100M12/24.B.2021

 

EN 

 

THE PRESENT MANUAL BELONGS TO - 

Schenker Italia 

-  ALL RIGHTS RESERVED 

25 

4.5  Electric connections 

  ATTENTION 

 

These  steps  have  to  be  performed  by  a  qualified  technician/operator,  by  referring  to  the 
electrical drawings provided within this document. 

 

4.5.1 

Remote control panel mounting 

The remote control panel has the following dimensions: 

width 100 mm.   

height 66 mm. 

It can be fixed on any internal vessel panel, provided that the area behind is free of humidity and condense 
and there is enough depth to house the rear part of the panel (approx. 8 cm.). 
 
The cut to be performed on the vessel covering panel, to encase the remote control panel, has the following 
dimensions: 

width 80 mm.    height 50 mm. 

 
The remote control panel can be connected through the pre-wired multiple cable of a 10mt standard length 
provided. It is possible to adapt the panel to a longer distance by adding a one more cable in series to the one 
provided. 
 

 

 

 

 

REMOTE CONTROL PANEL  

FIG. 4-3 

 

Summary of Contents for MODULAR 100













































Reviews: