Enter the Setup Mode
Enter the
Setup Mode
Administrator Recognition
Administrator
＊
Press the No. 00~ 99
＊
Press
the No.
Enter
Exit Setup Mode
Exit Setup Mode
PIN Code/ RFID Keycard Setup
1. The admin. and user PIN code cannot be 000000/111111/123456.
2. Blue light flashes if the NO. has been setup.
Notice
3. 3 beeps (red light) mean failed operation.
4. The system exit setup mode without any action over 5 seconds, two beeps (blue light).
User Setup
1
3
4
5
2
＃
Press the Up Button on
the back of the lock for 2
seconds until hear two
beeps.
Input admin. PIN code and
then press to confirm or
position the admin. card to
the sensor.
＃
04 ~ 97
＊ ＊
Press the No.
Enter the intended PIN
code (consistsof 4-8 digits),
and then press to
confirm or position the card
to the sensor.
＃
Single-Entry User Setup
Other Setup
User Deletion
1 2 3 4
＃
Press the Down
Button on the
back of the lock
for 2 seconds
until hear two
beeps.
Input admin. PIN
code and then
press to confirm
or position the
admin. card to the
sensor.
＃
Enter the No. you
intend to delete
( 01 ~ 97),
and then press
to confirm or
position the card.
＃
＊
＊
Volume Setup
1 2 3 4 5
＃
Press the Up
Button on the
back of the lock
for 2 seconds
until hear two
beeps.
Input admin.
PIN code and
then press
to confirm or
position the
admin. card to
the sensor.
＃
Press
the No.
99
＊
Press
00(mute),
01(low),
02(medium) or
03(loud), and
then press
to confirm.
＃
1 2 3 4
All User Deletion
＃
Press the Down
Button on the
back of the lock
for 2 seconds
until hear two
beeps.
Input admin. PIN
code and then
press to confirm
or position the
admin. card to the
sensor.
＃
Press the Down
Button on the back
of the lock for 5
seconds until hear
a continuous beep
and two short beeps
mean successful
reset.
Factory Default Setting
Problem
Continuous beeps after successful
operation
No reaction when entering Keycards/
PIN codes
Light doesn’t go off
Low battery alert. Replace the battery
immediately.
Battery is dead. Please use the key to
unlock.
Consecutive Keycards/PIN codes entry
errors. Pleae try again after 1 minute.
Replace batteries.
Indication
Troubleshooting
Important Notes
1
3
4
5
2
＃
Press the Up Button on
the back of the lock for 2
seconds until hear two
beeps.
Input admin. PIN code and
then press to confirm or
position the admin. card to
the sensor.
＃
Press the No.
98
＊
Enter the intended PIN
code (consistsof 4-8 digits),
and then press to
confirm or position the card
to the sensor.
＃
Administrator Setup
- First time setup
1
3
4
5
2
＃
2
Press the Up Button on
the back of the lock for 2
seconds until hear two
beeps.
Input the factory default
admin. PIN code (123456)
and then press to
confirm.
＃
Input admin. PIN code and
then press to confirm or
position the admin. card to
the sensor.
＃
00/ 01
02/ 03
＊ ＊
＊ ＊
Press the No.
Enter the intended admin.
PIN code (consists of 4-8
digits), and then press
to confirm or position the
admin. card to the sensor.
＃
- Admin. already setup
1. Remove one battery.
2. Next, while continuously pressing the two buttons on the back, reinstall the
battery.
A continuous beeps (red light) and a short beep (blue light) after successful
operation.
1. If the card is losing, please delete right away.
* Notice
：
The administrator (*00) can’t be deleted individually.
2. Please use alkaline batteries only.
3. To preserve the cleanliness of the product, wipe it down using a clean cloth.
Do not use alcohol or other chemical agents.
4. Please handle the lock carefully to ensure normal operation.
5. If you encounter any problem, please refer to the user manual first. If you still
have questions, please feel free to contact us or email us.
Enter the Intended PIN
Code or Card
Recognition
Enter the
Setup Mode
Administrator
Enter
Exit
Setup Mode
Recognition