manualshive.com logo in svg

Scantronic Multiscan Nursecall, Manager Manual

Share
Download
Scantronic Multiscan Nursecall Manager Manual Download Page 16

SYSTEM FAULT

LOW TX BATTERY

Should an intermittent low tone be emitted from the RDU bleepers, a system fault has
occurred. Where appropriate, the user should take the necessary corrective action.

Transmitter battery low.
Replace battery.

14

SYSTEM FAULT
TX JAMMED ON

Faulty transmitter.
Call engineer.

SYSTEM FAULT

CARRIER JAMMING

Radio Interference
Call engineer.

SYSTEM FAULT

RDU MISSING

A Remote Display Unit programmed as 'Fixed' has been
removed or is faulty.
Re-fit RDU if unplugged or call engineer if
n e c e s s a r y .

SYSTEM FAULT

RDU ERROR

Faulty Remote Display Unit.
Call engineer.

SYSTEM FAULT

MAINS FAIL

Mains supply has failed, the system will continue to run on
stand-by batteries for 20 hours (approx) if the battery is
fully charged.
Check cause of mains failure.

SYSTEM FAULT

LOW 12V BATTERY

The system internal battery is low. This will only occur after
mains fail. Reconnect mains if possible.

Communication problem with computer/printer.
Call engineer.

SYSTEM FAULT

RS232 ERROR 1/2

SYSTEM FAULT

PAGER ERROR

Check Pager is switched on and operating correctly. Call
engineer if necessary.

SYSTEM FAULT

LID TAMPER

The base station lid has been opened.
Call engineer.

     S

YSTEM 

F

AULT

 M

ESSAGES

9

SYSTEM FAULT

BUTTON JAMMED

Wiring fault, or RDU fault.
Call engineer.

Summary of Contents for Multiscan Nursecall





















Reviews:

No comments

Brands by name

Popular brands

Load more brands