Page 13
Step 3. Tension adjustment of the door spring
1. The door springs are set at the factory to the proper tension for the
outer door. If aesthetic wooden panel are installed, you will have to
adjust the door spring tension. Rotate the adjusting screw to drive
the adjustor to strain or relax the steel cable.
2. Door spring tension is correct when the door remains horizontal in
the fully opened position, yet rises to a close with the slight lift of
a finger.
Step 4. Dishwasher installation steps
Please refer to the specified installation steps in the installation drawings.
1. Affix the condensation strip under the work surface of cabinet. Please ensure the condensation strip is
flush with edge of work surface. (Step 2)
2. Connect the inlet hose to the cold water supply.
3. Connect the drain hose.
4. Connect the power cord.
5. Place the dishwasher into position. (Step 4)
6. Level the dishwasher. The rear food can be adjusted from the front of the dishwasher by turning the
Philips screw in the middle of the base of dishwasher use an Philips screw. To adjust the front feet, use
a flat screw driver and turn the front feet until the dishwasher is level. (Step 5 to Step 6)
7. Install the furniture door to the outer door of the dishwasher. (Step 7 to Step 10)
8. Adjust the tension of the door springs by using an Allen key turning in a clockwise motion to tighten the
left and right door springs. Failure to do this could cause damage to your dishwasher. (Step 11)
9. Connect the drain hose.
A. Normal work surface: Put the installation hook into the slot of the side plane and secure it to the
work surface with the wood screws.
B. Marble or granite work top: Fix the side with Screw.
4. Installation Instruction
Step 3. Tension adjustment of the door spring
1.
The door springs are set at the factory to
the proper tension for the outer door. If
aesthetic wooden panel are installed, you
will have to adjust the door spring tension.
Rotate the adjusting screw to drive the
adjustor to strain or relax the steel cable.
2.
Door spring tension is correct when the
door remains horizontal in the fully opened
position, yet rises to a close with the slight
lift of a finger.
Install the hook on the aesthetic wooden panel and put the hook into the slot of the
outer door of dishwasher (see figure A). After positioning of the panel, fix the panel
onto the outer door by screws and bolts (See figure B).
B
2
.
Pin up the four long screws
A
1
.
Take away the four short screws
Full-integrated
model
21
Step 4. Dishwasher installation steps
1.
Affix the condensation strip under the work surface of cabinet. Please ensure the
condensation strip is flush with edge of work surface. (Step 2)
2.
Connect the inlet hose to the cold water supply.
3.
Connect the drain hose.
4.
Connect the power cord.
5.
Place the dishwasher into position. (Step 4)
6.
Level the dishwasher. The rear food can be adjusted from the front of the
dishwasher by turning the Philips screw in the middle of the base of dishwasher
use an Philips screw. To adjust the front feet, use a flat screw driver and turn the
front feet until the dishwasher is level. (Step 5 to Step 6)
7.
Install the furniture door to the outer door of the dishwasher. (Step 7 to Step 10)
8.
Adjust the tension of the door springs by using an Allen key turning in a clockwise
motion to tighten the left and right door springs. Failure to do this could cause
damage to your dishwasher. (Step 11)
9.
The dishwasher must be secured in place. There are two ways to do this:
A.
Normal work surface: Put the installation hook into the slot of the side plane and
secure it to the work surface with the wood screws.
B.
Marble or granite work top: Fix the side with Screw.
A
B
22
Please refer to the specified installation steps in the installation
drawings.