28
Never use sharp objects, scouring pads or harsh cleaners on any
part of the dishwasher.
Cleaning The Door
To clean the edge around the door, you should use only a soft
warm, damp cloth. To avoid penetration of water into the door
lock and electrical components, do not use a spray cleaner of
any kind.
• Never use a spray cleaner to clean the door panel as it may
damage the door lock and electrical components.
Warning: Abrasive agents or some paper towel should not be
used because of the risk of scratching or leaving spots on the
stainless steel surface.
Cleaning the Spray Arms
It is necessary to clean the spray
arms regularly for hard water
chemicals will clog the spray
arm jets and bearings.
To remove the upper spray arm,
hold the nut, rotate the arm
clockwise to remove it.
To remove the lower spray arm,
pull out the spray arm upward.
Wash the arms in soapy and
warm water and use a soft
brush to clean the jets. Replace
themafter rinsing them thoroughly.
Keep your dishwasher in good shape
• After every wash, turn off the water supply to the appliance
and leave the door slightly open so that moisture and odors
are not trapped inside.
Remove the Plug
• Before cleaning or performing maintenance, always remove
the plug from the socket.
No Solvents or Abrasive Cleaning
• To clean the exterior and rubber parts of the dishwasher, do
not use solvents or abrasive cleaning products. Only use a
cloth with warm soapy water.
• To remove spots or stains from the surface of the interior,
use a cloth dampened with water with a little vinegar, or a
cleaning product made specifically for dishwashers.
When not in use for a long time
It is recommend that you run a wash cycle with the dishwasher
empty and then remove the plug from the socket, turn off the
water supply and leave the door of the appliance slightly open.
This will help the door seals to last longer and prevent odours
from forming within the appliance.
Moving the Appliance
If the appliance must be moved, try to keep it in the vertical
position. If absolutely necessary, it can be positioned on its back.
Seals
One of the factors that cause odors to form in the dishwasher is
food that remains trapped in the seals. Periodic cleaning with a
damp sponge will prevent this from occurring.
Installation instructions
Disconnect electrical power and electrical equipments before
installing dishwasher. should be done by qualified profes-
sionals. Failure to do so can result in death or electrical shock.
Preparation
The installation position of dishwasher should be near the exist-
ing water inlet tap and drain outlet and power socket. One side
of the cabinet sink should be chosen to facilitate the connection
of drain hoses of the dishwasher.
Positioning the appliance
Position the appliance in the desired location. The back should
rest against the wall behind it, and the sides, along the adjacent
cabinets or wall. The dishwasher is equipped with water supply
and drain hoses that can be positioned to the right or the left to
facilitate proper installation.
Power connection
For personal safety:
• Do not use an extension cord or an adapter plug with this
appliance.
• Do not, under any circumstances, cut or remove the earth-
ing.
Electrical requirements
Please look at the rating label to know the rating voltage and
connect the dishwasher to the appropriate power supply. Use the
required fuse 10 amp, time delay fuse or circuit breaker recom-
mended and provide separate circuit serving only this appliance.
Connection from the power cord.
Ensure the voltage and frequency of the power being corre-
sponds to those on the rating plate. Only insert the plug into an
electrical socket which is earthed properly. If the electrical socket
to which the appliance must be connected is not appropriate for
the plug , replace the socket, rather than using a adaptors or the
like as they could cause overheating and burns.
Cold water connection (safety hose)
The appliance must be connected
to the water mains using new
hose-sets. The old hose-sets should
not be reused.
Water pressure must be between
0,04 MPa and 1 MPa. If the pres-
sure is below the minimum consult
our Service Department for advice.
1 Pull The safety supply hoses completely out from storage
compartment located at rear of dishwasher.
2 Tighter the screws of the safety supply hose to the faucet
with thread 3/4inch.
3 Turn water fully on before starting the dishwasher.
The safety supply hose consists of the double walls. The hose’s
system guarantees its intervention by blocking the flow of wa-
ter in case of the supply hose breaking and when the air space
between the supply hose itself and the outer corrugated hose is
full of water.
