background image

1

1.1 INTRODUCTION

This manual has been prepared to provide the
information you need to correctly assemble, operate,
and maintain this grass catcher.  Read it carefully and
keep it for future reference.

The replacement of any part on this product by other
than the manufacturer's authorized replacement part
may adversely affect the performance, durability or
safety of this product.

USE OF OTHER THAN ORIGINAL SCAG
REPLACEMENT PARTS WILL VOID THE
WARRANTY.

If additional information or service is needed that is
not outlined in this manual, please contact your Scag
Power Equipment dealer.  Scag dealers are trained in
the latest service methods and carry a full line of Scag
replacement parts.

When ordering parts, always provide the complete
model number of your catcher.

All information provided in this manual is based upon
information available at the time of printing.  Scag
Power Equipment reserves the right to make changes
at any time without notice or obligation.

A replacement manual is available from your
authorized Scag Service Dealer or by contacting:
Scag Power Equipment, Service Department at P.O.
Box 152, Mayville, WI 53050.  You may also contact
us through our website at www.scag.com  The
manual for this grass catcher can be downloaded by
using the model and serial number or use the contact
form to make your request.  Please indicate the
complete model and serial number of your Scag
product when requesting replacement manuals.

1.2 DIRECTION REFERENCE

The "Right" and "Left", "Front" and "Rear" of the
machine are referenced from the normal operating
position.

2. Before dumping the debris, disengage the

mower, stop the engine and wait for all
movement to stop.

3. ALWAYS turn the engine OFF, remove the key

and wait for all movement to stop before
servicing or cleaning the mower or the grass
catcher.

4. Do not modify or alter any component of the

grass catcher attachment or mower.

5. Do not allow any passengers to ride on the grass

catcher attachment or on the mower.

WARNING

WARNING

DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING
KIT, OR ENTIRE GRASS CATCHER INSTALLED

2.1 SAFETY AND OPERATING
       INSTRUCTIONS

-NOTE-

To avoid personal injury, it is imperative that
all safety instructions be observed.

1. Read this operator's manual and the

operator's manual that is supplied with the
machine this attachment is used on.

DANGER

DANGER

ROTATING BLOWER

BLADES

STOP ENGINE BEFORE

ENTERING CHUTE

CONTACT CAN INJURE

2.2 GRASS CATCHING OPERATION

1. With the hopper door closed, engage the deck

drive.

2. Proceed to mow until the hopper is full.

Summary of Contents for GC-STT-CSV





















Reviews: