SBM SB-2000 Service Manual Download Page 77

Page: 77 / 121

Currency Discrimination Fitness Sorter SB - 2000 Service Manual

③

In case Boot in flash memory is damaged, it is impossible to upgrade even in SOS mode,

therefore, please be careful.

2) Upgrade by using USB memory stick

①

Save *.swp file in USB-File Folder to Root folder in USB memory stick.

②

Press “MENU



1(USB DOWN LIST)”, then, the machine will be USB memory mode

as Pic 1.

③

If USB memory stick is not properly inserted or if USB memory stick which is not

compatible with the machine is used, USB:ERROR will happen. In this case, remove and

insert USB memory stick again or use different USB memory stick.

④

If there is no problem with the connection with USB memory stick, LCD will be displayed as

△▽

Pic 3. Select the file for upgrade by using

key and press “START” key to upgrade the

machine.

⑤

At this time, the message “Please Wait 40 seconds…” will be displayed as Pic 4. and the

machine will be automatically turned off and on after upgrade is finished.

⑥

Do not turn off the machine and wait until the machine is automatically turned off.

Pic 1. Main B’d

Pic 2. Image B’d

Summary of Contents for SB-2000


























































































































Search results

Summary of Contents for SB-2000

Reviews:

Brands by name

Popular brands

SBM SB-2000, Service Manual

Search results

Summary of Contents for SB-2000

Reviews:

Brands by name

Popular brands