SBG Navsight Apogee IMU Hardware Manual Download Page 59

Page: 59 / 74

Navsight Solution

– Hardware Manual

NAVSIGHTHM.1.3

7.7.3. CA-AEK-PWR-3M

This cable mates with the PWR connector to power up the Navsight solution
from an external power supply.

●

1 x ODU Mini-Snap F Series S31F1C-P02LPN0-0002 plug

●

1 x open end

●

IP-68 rating

●

3m long 18AWG cable

●

Weight: 170g

Cable wiring is:

Signal

Color

SHIELD

VIN+

Red

VIN-

Black

7.7.4. CA-NAVS-ETH-5M

This cable provides a direct access to Ethernet network thanks to its RJ-45
plug.

●

Direct connection on ETH port

●

1 x RJ-45 connector for Ethernet connection.

●

5 m cable (CAT6 type)

●

Weight: 120g

Note: This cable is included in the rugged processing unit package. It can also be ordered separately.

59/74

Figure 7.8 : Alternative

Power cable

Figure 7.9 : Ethernet cable

Summary of Contents for Navsight Apogee IMU











































































Search results

Summary of Contents for Navsight Apogee IMU

Reviews:

Related manuals for Navsight Apogee IMU

Brands by name

Popular brands

SBG Navsight Apogee IMU, Hardware Manual

Search results

Summary of Contents for Navsight Apogee IMU

Reviews:

Related manuals for Navsight Apogee IMU

Brands by name

Popular brands