SBG Navsight Apogee IMU Hardware Manual Download Page 48

Page: 48 / 74

Navsight Solution

– Hardware Manual

NAVSIGHTHM.1.3

5.13.2. Electrical specifications

Parameter

Min.

Typ.

Max.

Units

Conditions

Operating voltage

VDC

Power consumption

Navsight-E with Ekinox2-I

Navsight-E with Apogee-I

Navsight-T/S with Ekinox2-I

Navsight-T/S with Apogee-I

Allowable Input Voltage Ripple

400

mV p-p

Under voltage lock out

11.5

Turn on threshold

8,5

Turn off threshold

Galvanic Isolation

250

VDC

VIN+ to Mechanical Ground
VIN- to Mechanical Ground

5.14. Typical wiring recommendations

In this section, we briefly describe a few recommended wiring diagrams.

5.14.1. Power supply connection

Concerning power supply, we recommend shielded cable, with at least AWG 24 wires.

48/74

Figure 5.21: Power supply wiring connections

NAVSIGHT

Power Connector

Power Supply

Shield is the mechanical ground.
Connected to Navsight Enclosure

VCC

GND

SHIELD

+12 to 36V DC

Summary of Contents for Navsight Apogee IMU











































































Search results

Summary of Contents for Navsight Apogee IMU

Reviews:

Related manuals for Navsight Apogee IMU

Brands by name

Popular brands

SBG Navsight Apogee IMU, Hardware Manual

Search results

Summary of Contents for Navsight Apogee IMU

Reviews:

Related manuals for Navsight Apogee IMU

Brands by name

Popular brands