SBC PCD2 Series Manual Download Page 138

Page: 138 / 330

Saia-Burgess Controls AG

Manual I/O-modules for PCD1 │ PCD2 series │ Document 27-600 – Release ENG09 │ 2019-05-01

5-129

I/O modules PCD1|PCD2

PCD2.H32x

5.19.2

PCD2.H32x, motion control modules for servo-drives

There are four module types available:

PCD2.H320:

2 axes with 24 V encoder

PCD2.H325:

2 axes with 5 V and SSI absolute value encoder

PCD2.H322:

1 axis (slave operation) with 24 V encoder

PCD2.H327:

1 axis (slave operation) with 5 V and SSI absolute value encoder

The PCD2.H32x motion control modules are intelligent I/O modules in the PCD2

series. They are used to position two independent axes, with one variable speed

AC or DC drive (servo-motor) each, or two axes as an electronic transmission.

This requires the drive unit to have a power stage and incremental shaft encoder

for capturing position or speed. Displacement control may also be achieved with

an SSI absolute value encoder.

Each module contains a DSP processor that independently controls every

movement according to parameters supplied by the user program: velocity,

acceleration and destination position (“PID control”). This enables each axis

to execute independent movements, perform S-curve and trapezoidal motion

profiles, change velocity and acceleration, perform interrupt functions and record

the current axis position during motion.

In a PCD2 with expansion housing, up to 7 PCD2.H32x modules can be operated

in parallel.

Technical data

Function-specific data

Number of systems:

2 for H320/5
1 for H322/7 + 1 H100 counter input 4 DI + 1 DO

Motion parameters

31-bit registers are used for destination position, velocity and acceleration, numerical

range ± 2

)

Position

Units and resolution selectable (depending on mechanical

factor)

Velocity

Units and resolution selectable (depending on mechanical

factor)

Acceleration

Units and resolution selectable (depending on mechanical

factor)

PID controller

Sample time 100 µs / axis, programmable proportional,

integral and differential factors. Sample time for differential

part can be programmed separately. Additional velocity and

acceleration feed-forward (all 16 bit values)

Analogue controller

output

Velocity set point ± 10 V

(resolution 12 bit)

Counting frequency max. 125 kHz for H320/5

max. 250 kHz for H322/7

Summary of Contents for PCD2 Series











































































































































































































































































































































Search results

Summary of Contents for PCD2 Series

Reviews:

Related manuals for PCD2 Series

Brands by name

Popular brands

SBC PCD2 Series, Manual

Search results

Summary of Contents for PCD2 Series

Reviews:

Related manuals for PCD2 Series

Brands by name

Popular brands