background image

1.  You must install a rip fence before using your saw. Attempting to use the saw without a rip fence could result in 

serious personal injury.

2.  Always use a rip fence when making rip cuts. Never perform a ripping operation freehand or a serious injury 

may result.

3.  Always use a push stick or push block when your hand comes within 6 inches of the blade. Attempting to use 

the rip fence for narrow cuts without a push stick or push block could result in a serious injury.

4.  Do not use the miter gauge when making rip cuts.

5.  While making bevel cuts, use the fence only on the right side of the saw blade to prevent the blade from 

possibly contacting the fence. The brake will activate if the spinning saw blade comes into contact with the 

metal in the fence.

Safety

Warranty

SawStop warrants to the original  retail purchaser  of a new T-Glide Fence System - Industrial Series from 

an authorized SawStop distributor that the fence system will be free from defects in material and workmanship 

for TWO YEARS from the date of purchase. SawStop warrants to the original retail purchaser of a refurbished, 

demonstration or floor model T-Glide Fence System - Industrial Series from an authorized SawStop distributor that 

the fence system will be free from defects in material and workmanship for ONE YEAR from the date of purchase.

This  warranty  does  not  apply  to  defects  arising  from  misuse,  abuse,  negligence,  accidents,  normal  wear-

and-tear, unauthorized repair or alteration, or lack of maintenance. This warranty is void if the fence system or any 

portion of the fence system is modified without the prior written permission of SawStop, LLC, or if the fence system 

is located or has been used outside of the country where the authorized SawStop distributor from whom the fence 

system was purchased resides. 

Please  contact  SawStop  to  take  advantage  of  this  warranty.  If  SawStop  determines  the  fence  system  is 

defective  in  material  or  workmanship,  and  not  due  to  misuse,  abuse,  negligence,  accidents,  normal  wear-and-

tear, unauthorized repair or alteration, or lack of maintenance, then SawStop will, at its expense and upon proof 

of purchase, send replacement parts to the original retail purchaser necessary to cure the defect. Alternatively, 

SawStop will repair the fence system provided it is returned to SawStop, shipping prepaid, with proof of purchase 

and within the warranty period.

SawStop disclaims any and all other express or implied warranties, including merchantability and fitness for a 

particular purpose. SawStop shall not be liable for death, injuries to persons or property, or incidental, consequential, 

contingent or special damages arising from the use of the fence system.

This warranty gives you specific legal rights. You may have other rights which vary from state to state.

Summary of Contents for T-Glide Industrial Series



















Reviews: