Savin Aficio SP 4100N Operating Instructions Manual Download Page 233

Page: 233 / 344

Getting Printer Information over the Network

This section explains details of each item displayed in the printer status and information.

Current Printer Status

The printer status can be checked using the following commands:

• UNIX: Use the "lpq" command and "rsh", "rcp", "ftp" and "sftp" parameters.
• mshell: Use the "status" command.

Messages

Description

Access Restricted

The job was canceled because user have no
authority.

Adjusting...

The printer is initializing or calibrating.

Call Service Center

There is a malfunction in the printer.

Canceled

The job is reset.

Canceling Job...

The job is being reset.

Configuring...

Setting is being changed.

Cooling Down Fusing Unit...

Fusing unit is cooling down.

Cover Open: Duplex Unit

The cover of the duplex unit is open.

Cover Open: Front Cover

The front cover is open.

Empty: Black Toner

The black toner cartridge is almost empty.

Energy Saver Mode

The printer is in Energy Saver Mode.

Error

An error has occurred.

Error: DIMM Value

A memory error occurred.

Error: Ethernet Board

An Ethernet board error has occurred.

Error: HDD Board

A hard disk drive board error has occurred.

Error: Optional Font

An error has occurred in the font file of the printer.

Error: Parallel I/F Board

An error has occurred in the parallel interface.

Getting Printer Information over the Network

231

Summary of Contents for Aficio SP 4100N
























































































































































































































































































































































Search results

Summary of Contents for Aficio SP 4100N

Reviews:

Related manuals for Aficio SP 4100N

Brands by name

Popular brands

Savin Aficio SP 4100N, Operating Instructions Manual

Search results

Summary of Contents for Aficio SP 4100N

Reviews:

Related manuals for Aficio SP 4100N

Brands by name

Popular brands