Savant WIF 104 Series, Quick Reference Manual

Page: 1 / 2

The Savant WIF-SWS104 (snow white) and WIF-LAS104 (light almond) wireless fan controllers incorporate a push button rotary dial
that controls low, medium, and high speed on a 120V AC fan. In addition to the push button rotary dial, the front panel incorporates
three LEDs which are a quick indicator of the current fan speed.
The fan controller can replace any existing standard 120V AC fan controller or switch that is wired into a standard 3-wire configuration
(No Neutral not supported).
Finally, the Savant Fan Controller communicates with most 802.11 b/g/n wireless networks. Once communicating with the local LAN, the
fan controller can be added to the Savant Control system to remotely control any fan through most iOS® or Android® devices.
IMPORTANT! Using this product in a manner that is not consistent with this document will void your warranty
Box Contents
•
Metropolitan Fan controller without faceplate
•
(2) Mounting Screws 6/32 x ¾ inch
•
(4) Wire Nuts
•
Quick Reference Guide (this document)
Optional Accessories
•
1 to 4-Gang Faceplates
•
Black conversion kits
Specifications
Environmental Environmental
Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 90% Relative Humidity (non-condensing)
Location Indoor Use Only
Dimensions Dimensions
Height 4.13 in (10.49 cm) / Shipping 7.0 in (17.78 cm)
Width 2.38 in (6.05 cm) / Shipping 4.5 in (11.43 cm)
Depth 1.81 in (4.60 cm) / Shipping 3.0 in (7.62 cm)
Weight (Shipping) 0.60 lb (0.272 kg)
Recommended Back Box Depth Dimensions Recommended Back Box Depth Dimensions
All Metro fan controllers require a standard U.S. electrical back box
• Recommended - 3.5 in (8.89 cm) deep
• Minimum - 2.25 in (5.72 cm) deep All Metro fan controllers require a standard U.S. electrical back box
• Recommended - 3.5 in (8.89 cm) deep
• Minimum - 2.25 in (5.72 cm) deep
Power Power
Input 120V AC at 60Hz
Load Power (Max) 180W 1.5A @ 120V AC
Supported Load Types Supported Load Types
Fan (
120V AC )
Fan (
120V AC )
Standards Standards
Wireless 802.11 b/g/n
Security WPA1™, WPA2™, WPA1™+WPA2™, WEP
Regulatory Regulatory
Safety and Emissions
FCC Part 15 | UL
For more details, refer to the
Regulatory section
Contains FCC ID: TLZ-CU277
Contains IC: 6100A-CU277
RoHS Compliant
Minimum Supported Release Minimum Supported Release
Savant® OS da Vinci® 7.2.1
Front View
A
Ambient Light Sensor - Senses the level of ambient light in the room and adjusts the LED brightness on the front panel.
The ambient light sensor operation can be modified in Blueprint.
B
Reset Button - The reset button has two functions:
• Press and release the reset button. After button is released, all LEDs on the front panel illuminate for two seconds and
then flash twice. Pressing the reset button causes the fan controller to calibrate itself to the circuit it is being installed
to. After the fan controller calibrates itself, it then reboots. After the reboot, the LED sequencing is determined by
whether the device had previously been connected to a network. Refer to
LED Sequencing table.
Note: The reset button should always be pressed after the Metropolitan device is installed.
• Press and hold the reset button for five seconds until all LEDs on the front panel illuminate. The LEDs will remain on
for two seconds and then flash twice. The fan controller then reboots and reverts to Provisioning Mode. In
Provisioning Mode, the first two LEDs on the front panel blink in an alternating pattern waiting to be provisioned.
Refer to the
LED Sequencing table.
C
Rotary Dial/Button - Press the rotary button/dial to switch the load (fan) On and O ff . Once switched On, turning the
dial counterclockwise decreases the speed of the fan. Turning the dial clockwise increases the speed of the fan. The
three LEDs above the dial indicate speed of the fan. As the speed of the fan increase, more LEDs are lit. As the speed of
the fan decreases, less LEDs are lit. When configured in Blueprint, the LEDs track the scene configured.
D
Service Switch - The service switch removes power from the load (red wire). Toggle the service switch to O ff whenever
changing the load. The service switch can also be used to power cycle the fan controller.
Rear View
Device wires are all a five inch #16 AWG stranded wire.
Green
Ground - Wire to Gnd.
White
Neutral - Return path for voltage.
Red
Load - Wire to the load.
D
Black
Line - Wire to hot wire from AC power source.
Metropolitan Wireless Fan Controller | 009-1340-02 | 150604 45 Perseverance Way, Hyannis, MA 02601
Copyright © 2015 Savant Systems, LLC 1 of 2 Savant.com | 508.683.2500
Metropolitan Wireless Fan Controller WIF-xxx104
Quick Reference Guide
For Product Info