PAV-VOMVP1F2-xx/PAV-VOMVP1CP2-xx QRG | 009-2059-00
45 Perseverance Way, Hyannis, MA 02601
Copyright © 2022 Savant Systems, Inc | 220907
2 of 2
Savant.com | 508.683.2500
Rear Panel
DC 12V
IR Out
IR In
A
B
C
Loop In
D
HDMI Out
E
RS232
TX RX G
F
10 GbE (PoE+)
G
Audio Out
LAN
K
RESET
H
I
L M
J
N
Item
Description
A
Power Input 12V DC
B
IR In
Not Used
C
IR Out
3.5 mm IR Emitter connection. Transmits IR
signals via an IR Flasher (5V tolerant) to devices
with an IR input or IR receiver.
D
Loop In
Reserved for future use.
E
HDMI Out
19-Pin Type A HDMI female digital audio/video
output.
Supports HDMI 2.0a
HDMI 2.0 compliant cable required for 4K
content.
F
RS-232
3-pin control connector transmits and receives
serial data to and from serial controllable
devices. For pin-out information, refer to the
RS-232
Wiring section to the right.
G
10 GbE
10G input from the Audio/Video over IP switch.
SFP+ (PAV-VOMVP1F2-xx)
RJ-45 (PAV-VOMVP1CP2-xx) supports Power
over Ethernet (PoE+ IEEE 802.3at standard).
H
Link LED
Solid Green
- Link is established with
2.5/5GBase-T mode.
Solid Amber
- Link is established with 10GBase-T
mode.
Off
– No link established.
I
Link Activity
LED
Amber Blinking
- Indicates data activity.
Off
– No Activity.
J
Audio Out
3.5 mm (1/8 in) Analog Audio Output. Outputs
2 Ch PCM audio from the local HDMI input when
2 CH and MC PCM is present. Does not support
down mixing encoded audio. Direct Line Level 2.1
V
RMS
Output.
K
LAN
1G of reserved network data bandwidth
commonly used to connect any network
compliant device to transmit its data onto the
Ethernet network by sharing the 10G network
link. 8-pin RJ-45 female connection.
IMPORTANT!
: Do not connect this port to a
network switch.
L
Ljnk LED
Solid Orange
- Link is established.
Off
– No link established.
M
Link Activity
LED
Solid Orange
- Link is established.
Off
– No link established.
N
Reset
Hold down this button with a pointed stylus for
20 seconds while powering up the device to
restore the device to factory default settings.
Wiring and Connections
IR Wiring
IR connections are made using 3.5 mm
IR Emitter supplied with the device.
RS-232 Wiring
Serial control connection are made using a 3-pin
Control Connector supplied with the device. The
wire slips into the hole and locks with a screw
located at the top of the connector.
Optical In (PAV-VOMVP1F2-xx)
Enhanced small form-factor pluggable connection. Duplex LC Multi-
mode OM3 Fiber required.
Transport Distance
OM3 multi-mode fiber
1000ft (300m)
10 GbE (PoE+) (PAV-VOMVP1CP2-xx)
RJ-45 10G Ethernet connection.
Transport Distance
Cat6
100ft (30m)
Cat6a
300ft (100m)
Cat7
300ft (100m)
Installation
To install this device use the mounting screws to attach the included
mounting brackets. Please follow the steps below.
1. Align the bracket using the top holes.
NOTE
: This will leave an air gap behind the device.
2. Use mounting screws to attaching the bracket.
If the device is going to be mounted Savant recommends aligning the
device with the rear of the device facing down. This will allow the best
heat dissipation.
Rear Panel
Power Input
3
2
1
PIN 1
Ground
PIN 2
Transmit
PIN 3
Receive
Rx
Tx
G
