sauter Equitherm EQJW 125 User Manual Download Page 39

Page: 39 / 74

EQJW 125: Heating controller

Operation

7001029003 A

Set the rotary switch to PROG.

Turn the input knob to go to the calendar

programme.

Push the input knob; this selects the calendar

programme.

•

You see '_ _ _ _' or the first switching
command if one is present.

4.5.2

Viewing switching commands

Turn the input knob; the individual switching
commands are shown, if any are present.

•

An empty switching command is shown as
'_ _ _ _'.

4.5.3

Entering a switching command

Turn the input knob until you reach the next

empty switching command.

Push the input knob.

•

The new switching command is shown.

Turn the input knob.

•

The date for the switching command is
changed.

Push the input knob.

•

The date for the switching command is
confirmed.

Turn the input knob.

Select the mode for the switching command.

Push the input knob.

•

The mode is confirmed.

Summary of Contents for Equitherm EQJW 125











































































Search results

Summary of Contents for Equitherm EQJW 125

Reviews:

Related manuals for Equitherm EQJW 125

Brands by name

Popular brands

sauter Equitherm EQJW 125, User Manual

Search results

Summary of Contents for Equitherm EQJW 125

Reviews:

Related manuals for Equitherm EQJW 125

Brands by name

Popular brands