background image

12

SAFETY DEVICES

IMPORTANT : 

It is forbidden to bypass or tamper

with any of the safety devices. If, after attempting
to use the heater, a safety shut-down condition
occurs, this must be rectified immediately by a
qualified, competent person.

OPALIS 6 MODELS

The heater is fitted with a flue safety device. In the
event of total or partial obstruction of the flue
system or detrimental downdraught into the heater,
the safety device will shut off the heater requiring
a manual re-start. Restarting the heater must only
be carried out after waiting 15 minutes. Repeated
safety shutdown must be dealt with by a qualified,
competent person.

OPALIS 5 MODELS
Safety pilot atmospheric control

When the ambient atmosphere reaches a critical
vitiation threshold, the pilot is extinguished. The
thermocouple cools very rapidly thereby causing
the disconnection of the appliance, thereby auto-
matically cutting off the gas supply to the
appliance.

Heat exchanger - Blockage safety device

This device consists of a tube fixed onto the left side
of the combustion chamber. The other end rests
on a cradle integral with the stirrup fixed on the
burner bracket.
If the heat exchanger becomes blocked, the path
offered to the flue gases between the fins
decreases, and a stagnation of the combustion
products in the combustion chamber occurs, the
former tending to leak increasingly towards the
bottom of this chamber.
The tube permits recycling of the combustion prod-
ucts discharged at the level of the pilot. The
recycling flow rate of these products towards the
pilot increases as the heat exchanger becomes
more restrictive. When it reaches a critical threshold,
it extinguishes the pilot leading to an interruption of
the gas supply to the burner.

After a service call

, the technician must check the

blockage safety device is in working order :

Dismantle the deflector and place the test-

mesh bottom plate at the top of the heat
exchanger

Ignite the pilot and leave the pilot to operate

for a minimum of 2 minutes

start the appliance and check that the com-

plete extinction of the appliance takes place in a
time less than or equal to 40 seconds

replace the test mesh bottom plate with the

deflector.

Summary of Contents for OPALIS 5

















Reviews: