Satel abax 2 ARU-200 Quick Start Manual Download Page 4

ARU-200 

SATEL 

The  ARU-200  radio  signal  repeater  receives  transmissions  from  wireless  ABAX 2  system 
devices  and  retransmits  them.  This  manual  applies  to  the  repeater  supported  by  the 
ACU-220 and ACU-280 controllers with firmware version 6.03 (or newer). 

The repeater does not support the ABAX wireless devices. 

The firmware of the devices supported by the repeater cannot be updated remotely. 

 

1.  Features 

  Retransmission of signals from 46 wireless devices. 

  Encrypted two-way radio communication in the 868 MHz / 915 MHz frequency band (AES 

standard). 

  Transmission  channel  diversity 

–  4  channels  for  automatic  selection  of  the one  that  will 

enable  transmission  without  interference  with  other  signals  in  the  868 MHz / 915 MHz 
frequency band. 

  Remote update of repeater firmware. 

  LED indicator of the repeater status. 

  Tamper protection against cover removal. 

  Powered with 230 VAC. 

  Built-in switching power supply. 

  Short-circuit protection of the power input. 

  Backup battery. 

  Battery charging circuit. 

  Battery status supervision and low battery disconnect system. 

Summary of Contents for abax 2 ARU-200









Reviews: