manualshive.com logo in svg

Satec expertmeter EM720, Installation Manual

Share
Download
Satec expertmeter EM720 Installation Manual Download Page 9

 

Chapter 2 Installation

 

5 

 

Electrical Installation 

 

Before installing, ensure that all incoming power sources are shut 
OFF. Failure to observe this practice can result in serious or even fatal 
injury and damage to equipment. 

Primary electrical installation 

Before connecting the 

EM720 

to the power measurement terminals, remove the 

EM720 

front cover,

 

then

 

install the memory backup Lithium Battery backup (MBB) and Battery Pack Backup Power Supply (BPS) 

                

Figure 3: Memory Backup Lithium Battery and Battery Pack Installation 

 

 

Before installing the instrument, ensure that the Battery Pack Backup 
Power Supply (BPS) is connected. 

The BPS must be charged for a period of 16 consecutive hours before 
the installation.  

Charging the BPS, connect the instrument to a three phase Power 
source, according to the instrument inputs rating, to the Voltage 

Inputs: make sure there are no plug-in modules.  

 

Summary of Contents for expertmeter EM720

































Reviews:

No comments

Brands by name

Popular brands

Load more brands