background image

Configuration of the SAILOR 100 GX

 

 
 
 

Date: January - 2018 

Document Number: 95-159859-A 

 

 

 
 
 

 

Subject:  

Installation of the SAILOR 100 GX Antenna Diversity Solution

 

 
This document has the following sections: 

 

Introduction 

 

Installation of the dual-antenna mode 

 

Configuration of the SAILOR 100 GX ADS 

 

Installation flow see 

Figure 9: Flow chart

 on the last page  

 

 
 

1.1

 

Introduction 

The SAILOR 100 GX Antenna Diversity Solution (ADS) from Cobham 
SATCOM has the following unique features: 

 

Simple installation due to single cable antenna system. 

 

Cost effective solution using cables and COTS RF splitters, no need for 
additional 19" rack-mount units. 

 

Ensures maximum system uptime. 

 

Fully automatic switching to other GX VSAT antenna, no user intervention needed. 

 

Switching upon programmed blocking zones. 

 

Switching if tracking signal strength drops 4 dB below the signal strength in 
the idle antenna. 

 

Switching if the ADU is malfunctioning. 

 

Configured in minutes using the built-in web server user interface. 

 

 

 

 

 

 

 

 

Cobham SATCOM 

Lundtoftegaardsvej 93 D 
2800 Kgs. Lyngby 
Denmark 
 
T: +45 39 55 89 89 
F: +45 39 55 88 88

 

Summary of Contents for SAILOR 100 GX











Reviews: