![background image](http://html1.mh-extra.com/html/sata/51005c/51005c_operation-instruction-manual_1200205017.webp)
17
V_SC_51005C_202105
battery pack is exhausted, you can manually
rotate the machine to tighten or loosen the
screw. In this case, the chuck is stationary.
9. Drilling operation
When drilling on the surface of hard material,
first mark the area where you want to drill with
the pointed punch and hammer to prevent the
bit from slipping. Hold the hand drill, align the
bit tip with the mark, and press the switch to
drill. Drill with the appropriate pressure. Do not
apply excessive pressure or deviated pressure
to increase the diameter.
Note:
The intact high-speed steel bit shall be used for
the drilling on metal. For the short screwdriver
bit, use a magnetic connecting rod (not
included). When tightening the screw, apply a
little soap or other lubricant to the thread to
facilitate the operation.
QUESTION AND ANSWER:
1. Why does the machine not operate after the
switch is pressed?
A reversing yoke is located on the upper part of
switch. It is locked. Turn it to the position where
the rotation is in need, and then press the
button to rotate the machine.
2. Why does the hand drill stop when the screw
has not been tightened?
In this case, adjust the torque adjusting ring
between the body and chuck. The minimum
torque corresponds to position 1, and the
maximum torque corresponds to position xx.
Setting the torque adjusting ring to a higher
position can solve this problem.
3. Why is the service life of same kind of
battery pack is different?
As mentioned above, if a battery pack is left
unused for a long time, its service life may
be shortened. This is the matter of charging
frequency. Repeated charging and application
may improve the situation. In case of heavy
work, e.g. When the large screw is driven into
the hardwood, the battery pack will run out
soon. Do not charge in a temperature below
0 °C or above 45 °C. Otherwise, the performance
of battery pack will be affected.
MAINTENANCE
Be sure to pull off the plug before repairing
or replacing the machine.
The electric tool
does not require additional lubrication or other
maintenance. Do not wash the electric tool with
the water or chemical cleaner. Wipe it off with
a dry cloth. Tool shall be stored under the dry
conditions and kept clean at the vent of motor.
Try not to use it in a dusty environment.
DISPOSAL OF DISCARDED BATTERY
To protect the natural environment,
please recycle or dispose of the
battery pack properly. The battery pack
contains a Li-ion battery. Please consult
the local waste disposal department
for the information on recycling and/or
disposal. Exhaust the battery pack with
the hand drill, remove the battery pack,
and wrap the pole port with strong tape
to avoid the short circuit and leakage.
Do not attempt to open or remove any
part.
Summary of Contents for 51005C
