Input Options
Listening Options
Microphone
Select
M
on the mode switch
For general listening using either a plug in
or a long lead microphone to get right to
the sound source.
Plug the microphone into the socket with
the Microphone symbol.
Direct connection
Select
A
on the mode switch
To listen with maximum clarity to TV or
Audio from the SCART, RCA Phono or
Jack outputs.
Plug the appropriate lead into the socket
with the Microphone symbol.
Loop receiver
For non hearing aid users only.
Select
T
on the mode switch
Check or listen to an existing loop system
using headset or headphones.
Stethoscope Headset
Wear this lightweight headset under the
chin for maximum sound levels.
Headphones
Wear any conventional over the head
Headphones with 32 ohm impedance with
a 3.5mm stereo jack plug.
Earphones
Any in-ear earphones with a 3.5mm stereo
jack plug.
Neck Loop
Can be worn around the neck to transmit
the sound directly to the hearing aid on the
“T” or loop setting.
Ear hook
Worn adjacent to the behind the ear
hearing aid to transmit the sound directly
to the hearing aid on the “T” or loop
setting.
Direct connection to hearing aid
Direct connection to a hearing aid with the
appropriate facility and lead.
Beltclip/neckcord
To fit belt clip simply press the wings
of the clip into the position shown.
To remove the clip press one of the
wings away from the body.
Do not
try to remove the clip by lifting
the clip away from the battery cover as
you may damage the parts.
Push wings into
slots on base side
Push away
here
To fit the neck cord remove belt clip
and thread the cord as shown, and
replace the belt clip. The neck cord
has a safety release feature to avoid
you getting trapped by the cord.
Troubleshooting
Q. No Sound
A. Check headset/microphone are in the
correct sockets.
Headset or microphone may be faulty.
Batteries may be exhausted fit new
batteries.
Check operating mode.
Q. Low or distorted sound
A. Batteries nearly exhausted fit new
batteries.
Check operating mode.
Q. Feedback or squealing sound
A. Microphone is too close to headset
and volume is set too loud.
Q. Crackling or sound goes on and off
A. Dirty plugs - clean plugs
Faulty leads, wiggle leads to find
faulty lead - change lead
Q. Tinny or muffled sound
A. Tone control in wrong position
Headset ends can be removed for cleaning
and can be washed in warm soapy water
but must be thoroughly dried before
replacing.
If the system needs returning for repair
please send the complete system
including the amplifier, batteries and any
accessories purchased for the system.
Please state the nature of the fault and
your name and address of where you want
the system returned to. If the system is
still under guarantee please provide proof
of purchase otherwise we may need to
charge.
Specifications
Power requirements
2 X 1.5V AA/LR06 Alkaline batteries.
Battery life giving over 80 hours use with
a 32 ohm headset and average listening
levels.
Normal or rechargeable batteries may be
used with reduced life.
Dimensions
Approx L 95mm: W 62mm H25mm
excluding belt clip.
Weight
70g without batteries, approx. 120g with
batteries.
Material
ABS plastic casing.
Performance
Frequency Response:
200Hz-10 kHz +/- 3dB
Maximum Gain:
60dB
Tone Control:
+/- 8dB at 200Hz
+/- 8db at 5kHz
Maximum audio signal output:>125dB with
307-105 headphones.
Accessories/Spares
A full list of all Sarabec accessories and
spares is available on request.
330-009 Plug in Microphone
330-001 Standard microphone with
1.2m(4ft) black lead and
Velcro pads
330-044 Velcro pads kit one hook type
and three black loop pads. To
obtain just this replacement
kit, send two second class
stamps.
353-121 3m(10ft) Headphone/
Microphone extension lead
353-097 Crescendo direct audio lead
kit, including 5m(15)ft 3.5mm
jack plug to red/white Phono
plugs. Phono to SCART
adaptor, Phono to stereo jack
adaptor.
307-105 Stethoscope headset
303-055 Lightweight headphones
303-070 In-ear Earphones
201-125 Neck Loop
315-001 Single Ear hook
315-002 Dual Ear hooks
EU Declaration
of Confiormity
Sarabec Ltd hereby declares that the
Crescendo 60 amplifier is in compliance
with the relevant EU directives. The full
declaration is available from Sarabec Ltd
15 High Force Road, Middlesbrough, TS2
1RH, United Kingdom
All manuals and user guides at all-guides.com