background image

SPECIFICATIONS

General Specifications

Television system

NTSC standard system

Recording system

Rotary helical scan system

Number of heads

4, Double azimuth video
2, Audio FM

Format

VHS standard

Tape width

1/2 inch

Tape speed

SP : 33.35 mm/sec. (1.31

/sec.)

LP : 16.67 mm/sec. (0.65

/sec.) ..... (playback only)

SLP : 11.12 mm/sec. (0.43

/sec.)

Recording time

SP : 120 minutes with T-120 cassette
SLP : 360 minutes with T-120 cassette
SLP : 480 minutes with T-160 cassette

Fast forward/rewind time

approx. 43 seconds (T-120 tape)

Tuner receivable channels
(181 total)

TV Position

CATV Position

VHF channels

2-13

VHF channels

  1-13

UHF channels

14-69

Mid band channels

14-22

Super band channels

23-36

Hyper band channels

37-94, 100-125

Mid low band channels

95-99

RF converter

Built-in VHF converter

Converter output

Channel 3 or 4 selectable

Time indication

AM/PM 12-hour system

Timer

1 year/8-event programmable

Terminals

Antenna input

VHF/UHF:  F type

Antenna output

VHF/UHF:  F type

Video input/output

RCA jack

Audio input/output

RCA jack

Electrical Specifications

Video output level/impedance

1 V(p-p)/75 ohms

Audio output level/impedance

316 mV (–10 dBV)/less than 2.2 kohms

Video input level/impedance

500 mV(p-p) – 2.0 V(p-p)/75 ohms

Audio input level/impedance

316 mV (–10 dBV)/more than 47 kohms

Other Specifications

Power requirements

120 V AC, 60 Hz

Power consumption

17 watts

Dimensions (W x H x D)

360 mm x 97 mm x 277 mm (14.17

 x 3.82

 x 10.91

)

Weight (approximate)

3.0 kg (6.6 lbs.)

Remote control

B27900

The manufacturer reserves the right to modify product designs and specifications without notice and without incurring
any obligation.

SC4H/CA3 (VHR-H690 GB) Tue. Mar. 14/2000

42

Summary of Contents for VHR-H690













































Reviews: