■
CAMERA CONNECTIONS / SETTINGS
Do not connect the power cord until all other connections have
been completed.
1
Threaded holes for mounting (Top and Bottom)
• When using a camera mount base (sold separately) etc., use an attachment
screw shorter than 10 mm / 0.4 in. Otherwise, it may damage internal parts
of the camera.
• If you want to use a commercially available platform for the camera, select
an appropriate type, taking into consideration the gross weight of the
camera and platform, and secure it on a firm place.
• Images may blur under extremely bright lighting; adjust the lighting angle to
get clear images.
2
Supported coaxial cables:
RG-6U (5C-2V): 500 m / 546 yds max.
Following coaxial cables are also supported.
RG-11U (7C-2V): 600 m / 656 yds max.
RG-59U (3C-2V): 250 m / 273 yds max.
• RG-59U (3C-2V) can be used when distance between devices is short,
but not in duct or aerial routing.
• Using different cables from these specified here may attenuate the
video and/or sync signals and interfere with correct transmission.
VIDEO OUT
L L
ON
INT
BLC
BLC
OFF
EI
2
1
1
LEVEL
LINE
PHASE
AGC
2
+ –
GND
DC12V
AC24V
3
4
1/4”-20UNC
1
2
RG-6U (5C-2V):
500m/547 yds max.
Monitor
Thicker than 18 AWG
To prevent a fire hazard use
any UL listed wire rated VW-1.
Check that polarity is correct.
Thicker than 18 AWG
BNC type
The camera comes pre-adjusted and ready to install at time of factory
shipment.
1
Sync setting (LL/INT)
INT:
Internal sync
LL:
Line-Lock
(Only when using an AC power supply/Synchronizes
the unit with power frequency)
• If the vertical roll cannot be corrected by adjusting the PHASE dial on the
second and subsequent cameras, try adjusting the PHASE dial on the first
camera. If it still cannot be corrected, please check that the polarity of the
power cords of all connected devices is correct.
2
Iris setting (EI ON/OFF)
EI ON:
Electronic iris (manual or fixed iris lens) - For indoor use
EI OFF:
Auto iris
NOTE on Electronic iris setting (EI ON):
• Set the lens aperture to the shortest F stop.
• If fluorescent lighting is used where the camera is installed, the object will
flicker as a result. This type of phenomenon can be avoided by replacing the
fluorescent lighting with incandescent lamps.
• If the light entering the lens exceeds the maximum required illumination, the
image cannot be displayed properly. In that case, manually adjust the lens iris.
NOTE on Auto iris setting (EI OFF):
• If the entire image is too dark or too bright, adjust the contrast using the LEVEL dial.
3
Backlight compensation (BLC ON/OFF)
4
Automatic Gain Control (AGC ON/OFF)
AGC ON:
For automatically adjusting the sensitivity of the camera in
dark environments.
AGC OFF:
Fixed Gain is adopted for pictures with less video noise
under low light conditions.
Casino mode for VCC-5884EA:
This produces the best picture with a manual or fixed iris lens
especially under halogen lights, such as in a casino.
• White balance is adjusted automatically for best results under
halogen light (Color temperature: approx. 3000°K).
Do not use under fluorescent light or sunlight (approx. 5000°K).
A bluish image may be produced.
• Gamma Curve makes dark parts of the image brighter.
If the picture is out of focus at the telephoto position, adjust the
flange-back position.
&
Refer to "Flange-back adjustment" on back page.
BLC OFF
BLC ON (Only when using an auto iris lens)
For US and Canadian Users
Safety Guard
This installation should be made by a qualified service person and
should conform to all local codes.
For EU Users
For Russian Users
This product certified by official certification company
which is authorized by Russian Federation.
ДЛЯ
ПОЛЬЗОВАТЕЛЕЙ
РОССИЯ
Данная
продукция
сертифицирована
официальным
органом
по
сертификации
Российской
Федерации
.
THIS SYMBOL INDICATES THAT THERE ARE
IMPORTANT OPERATING AND MAINTENANCE
INSTRUCTIONS IN THE LITERATURE ACCOMPANYING
THIS UNIT.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
For the customers in Canada
This Class B digital apparatus complies with Canadian ICES-003.
Pour la clientèle canadienne
Cet appareil numerique de la Classe B est conforme à la norme
NMB-003 du Canada.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by
Sanyo
may void
the user's authority to operate this camera.
Please note:
Your SANYO product is designed and manufactured with
high quality materials and components which can be
recycled and reused.
This symbol means that electrical and electronic
equipment, at their end-of-life, should be disposed of
separately from your household waste.
Please dispose of this equipment at your local community
waste collection/recycling centre.
In the European Union there are separate collection
systems for used electrical and electronic products.
Please help us to conserve the environment we live in!
This symbol mark and recycle system are
applied only to EU countries and not applied to
countries in other areas of the world.
SANYO FISHER Sales (Europe) GmbH
Stahlgruberring 4, D-81829 München, Germany
SANYO Electric Co., Ltd.
1-1, Sanyo-cho, Daito City, Osaka 574-8534, Japan
English
Français
Deutsch
中文简体
L5CR2_XE(VCC-5995P_5884EA)(GB).fm 1 ページ ２００８年８月６日 水曜日 午後５時６分
