Sanyo VCB-3374 Instruction Manual Download Page 4

Safety Guard

THIS SYMBOL INDICATES THAT
THERE ARE IMPORTANT
OPERATING AND
MAINTENANCE INSTRUCTIONS
IN THE LITERATURE
ACCOMPANYING THIS UNIT.

WARNING:

TO PREVENT THE RISK OF FIRE OR
ELECTRIC SHOCK , DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR
MOISTURE.

This installation should be made by a
qualified service person and should
conform to all local codes.

ENGLISH

INFORMATION TO USER

For the customers in Canada

This Class B digital apparatus complies
with Canadian ICES-003.

Pour la clientèle canadienne

Cet appareil numerique de la Classe B
est conforme a la norme NMB-003 du
Canada.

This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and
can radiate radio frequency energy and,
if not installed and used in accordance
with the instructions, may cause
harmful interference to radio
communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does
cause harmful interference to radio or
television reception, which can be
determined by turning the equipment
off and on, the user is encouraged to
try to correct the interference by one or
more of the following measures:
– Reorient or relocate the receiving

antenna.

– Increase the separation between the

equipment and receiver.

– Connect the equipment into an

outlet on a circuit different from that
to which the receiver is connected.

– Consult the dealer or an experienced

radio/TV technician for help.

This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference,
and (2) this device must accept any
interference received, including
interference that may cause undesired
operation.
Changes or modifications not expressly
approved by 

Sanyo

 may void the user’s

authority to operate this camera.

L73K4/US  GB  1998, 3, 11

English

Summary of Contents for VCB-3374
















Reviews: