manualshive.com logo in svg

Sanyo SHA TM64 AGB, Instruction Manual

Share
Download
Sanyo SHA TM64 AGB Instruction Manual Download Page 13

.

3

Schedule Timer

NOTE

  If a program already exists in the copy destination group, the newly copied program overwrites the existing pro-

gram.

  If you accidentally copy over a program in the group program copy mode, holding down the CANCEL button for 

more than 2 seconds returns the program to the point prior to pressing the PROG. COPY GROUP button in STEP 1. (All 
changes and copy operations made up until that point are cleared.)

STEP 5 

Select other copy destination groups if desired.

 

You can copy the selected source group programs into other 
groups by repeatedly pressing the GROUP button to select a 
group followed by the SET button to set it.

NOTE

 

If a group from numbers 1 to 4 was selected as the copy desti-
nation group, that number appears in the program 

 area. If a 

group from numbers 5 to 8 was selected, that number appears in 
the program 

 area.

STEP 6 

Press the PROG. COPY GROUP button to enter the copied 
programs in the selected groups.

 

The normal display returns.

   

   

   

   

Summary of Contents for SHA TM64 AGB



























Reviews:

No comments

Brands by name

Popular brands

Load more brands