background image

-20-

WARNING:

- For continued safety, replace with a lamp assembly of the same type.
- Allow the projector to cool for at least 45 minutes before you open the

lamp cover. The inside of the projector can become very hot.

- Do not drop the lamp module or touch the glass bulb! The glass can

shatter and cause injury.

Procedure

1

Turn off the projector and disconnect the AC cord. Allow the projector to

cool for at least 45 minutes.

2

Remove a screw with a screwdriver and remove the lamp cover.

3

Remove 2 screws and pull out the lamp assembly by grasping the han-
dle.

4

Replace the lamp assembly securely and tighten 3 screws.

5

Place the lamp cover and tighten a screw.

6

Connect the AC cord to the projector and turn on.

Note:

- Do not reset the Lamp Replace Counter, except after lamp is replaced.
- The projector can not be turned-on with lamp cover removed, because

when the lamp cover is removed, the interlock switch is also released to
switch off the mains power for safety.

7

Reset the Lamp Replace Counter, see below explanation

.

Lamp Replacement

1

Turn the projector on, and press the 

MENU

button

and the on-screen menu will appear. Press the 

POINT

LEFT/RIGHT

buttons to move a red frame pointer to

SETTING menu icon.

2

Press the 

POINT DOWN

button to move a red frame

pointer to “Lamp counter reset” and then press the

SELECT

button. The message “Lamp replace counter

reset?” is displayed. Move the pointer to [Yes] and the
press the 

SELECT

button.

3

Another confirmation dialog box appears and select
[Yes] to reset Lamp Replace Counter .

Please refer to the owners manual for further informa-
tion.

Recommendation

Should the air filter become clogged with dust particles,
it will reduce the cooling fan’s effectiveness and may
result in internal heat build up and short lamp life. We
recommend cleaning the air filter after the projection
lamp is replaced.
Refer to “Air Filter Cleaning”.

Lamp cover

Lamp Assembly

Handle

ORDER REPLACEMENT LAMP

Type No.

Service Parts No.

POA-LMP35

610 293 2751

How to reset Lamp Replace Counter

The LAMP REPLACEMENT indicator will illuminate
when the Lamp Replace Counter reaches 1500
hours. This is to indicate that lamp replacement is
required.

You can check the lamp replace counter  following to
below procedure.

1

Press and hold the pointer 

UP

on the projector for

more than 20 seconds.

The  Lamp replace Counter is displayed on upper
left corner of the screen briefly.

* This model does not have Eco mode.

Normal

123 h

Eco

0 h

Total

123 h

Lamp replace counter data

How to check Lamp Replace Counter

Summary of Contents for PLC-SU32




















































































































































Reviews: